Bailey Infi 90 IMDSO15 Скачать руководство пользователя страница 16

Страница: 16 / 48

INTRODUCTION

SPECIFICATIONS

WBPEEUI240754A0

1 - 7

Environmental

Ambient temperature
(per IEC-68-2-1, 2,14)

Temperature rating within the cabinet or enclosure applies. INFI
90 OPEN internal cabinet rating: 0° to 70° C (32° to 158° F)

Relative humidity
(per IEC-68-2-3)

5% to 95% up to 55°C (131°F)(noncondensing)
5% to 45% at 70°C (158°F)(noncondensing)
Pollution degree: 1 (no condensation)

Atmospheric pressure

Sea level to 3 km (1.86 miles)

Air quality (per ISA S71.04, Class LA,
LB, LC - level 1)

Noncorrosive

CE Mark Declaration

EMC 89/336/EEC

Low Voltage Directive

73/23/EEC

This product, when installed in an INFI 90 OPEN cabinet, com-
plies with the following Directives/Standards requested for CE
marking:

EN50081-2 Generic Emission Standard - Part 2: Industrial
Environment
EN50082-2 Generic Immunity Standard - Part 2: Industrial
Environment

EN 61010 Safety Requirements for Electrical Equipment for
Measurement, Control and Laboratory Use - Part 1: General
Requirements

Certifications (pending)

CSA (Canadian Standards
Association)

FM (Factory Mutual)

Certification for use as process control equipment in an ordinary
(nonhazardous) location per CSA 22.2 No. 1010.1-92

Approval for the following categories:
Nonincendive for:
Class I, Division 2, Groups A,B,C,D
Class II, Division 2, Groups F,G

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.

Table 1-6. Relay Specifications

Property

Characteristic/Value

Type

1 Form C (SPDT)

Minimum load

12 V, 100 mA

Contact material

Silver cadmium oxide

Contact life (at 25°C [77°F])

30,000 operations at 7.2 FLA (full load current), 45 LRA (locked
rotor current), 120 VAC

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE

Table 1-5. Module Specifications

(continued)

Property

Characteristic/Value

Содержание Infi 90 IMDSO15

















































Результаты поиска

Содержание Infi 90 IMDSO15

Отзывы:

Похожие инструкции для Infi 90 IMDSO15

Бренды по названию

Популярные бренды

Bailey Infi 90 IMDSO15, Инструкция

Результаты поиска

Содержание Infi 90 IMDSO15

Отзывы:

Похожие инструкции для Infi 90 IMDSO15

Бренды по названию

Популярные бренды