manualshive.com logo in svg

Bailey IMMFP02, Инструкция по эксплуатации, Страница: 61 / 77

Поделиться
Скачать
Bailey IMMFP02 Скачать руководство пользователя страница 61

ON-LINE CONFIGURATION

OPERATION

I-E96-202B   

B - 3

Backup Cycle

The step numbers in this cycle correspond to the status of Fig-
ure 

B-1

.

Table B-2.  Backup Cycle

Primary

Backup

Procedure

n

00xx0x0x

n+1

10xx0x0x

1. Place the backup MFP module into execute mode. This saves a copy of the 
primary modules current configuration and enables it to be easily restored if 
needed.

n

01xx0x0x

n+1

00xx0x0x

2. Place the backup MFP module in configure mode.

The green LED of the backup MFP module blinks indicating configure mode. The 
module status also indicates configure mode. Configuration commands to the 
backup MFP module are sent to the address of the primary MFP module plus one 
(n+1). The primary MFP module now indicates that the backup MFP module is 
not available for automatic failover. Refer to bit 6 of the module status byte. 

To return to Step 1 without making any changes, place the backup MFP module 
in execute mode and reset it after LED 8 illuminates or the primary status indi-
cates 00xx0x0x. Resetting an MFP module causes all the LEDs on it to light 
momentarily before returning to normal status.

n

01xx0x0x

n+1

00xx1x0x

✲

When changes are being made to the backup MFP module, LED 7 blinks and bit 
3 of the backup module status is set indicating that the configurations of the 
backup and primary MFP modules do not match. If these changes to the config-
uration are incorrect, return to Step 1 by initializing the backup MFP module 
NVRAM memory while it is in configure mode.

NOTE:When configuring the backup MFP module, the following rules are strictly 
enforced by the module:

• Blocks can only be added in the block space at segment end.
• A block existing in the primary MFP module cannot be deleted.
• A specification change cannot be made to a block already existing in the pri-

mary MFP module if that change will affect the module RAM utilization factor 
(change memory requirements).

Any attempt to circumvent these rules will result in an appropriate error message.

n

01xx0x0x

n+1

00xx1x0x

✲

3. When an error exists in the new configuration, the backup MFP module enters 
error mode when attempting to transfer to execute mode. Return the module to 
configure mode and fix the error. The green status LED of the backup MFP mod-
ule blinks to indicate it is in the error or configure mode. The first byte of the 
module status also indicates the mode. Backup MFP module LED 7 blinks and 
bit 3 of the module status is set to indicate that configuration differences exist 
between the primary and backup.

n

01xx0x0x

n+1

00xx1x0x

✲

4. The backup MFP module can now be placed in execute mode provided no 
errors remain in the new configuration.

Make additional configuration changes by entering configure mode (Step 2). If 
no changes have been made, a backup MFP reset returns the backup module to 
the state of Step 1. If changes have been made, the backup module must be put 
into configure mode and initialized to get to the state of Step 1.

NOTE:  The transition from backup cycle step 4 to 5 occurs automatically after a 
successful Step 4 backup MFP module execute. The transaction completion 
time is MFP configuration dependent.

Содержание IMMFP02














































































Отзывы:

Нет отзывов