background image

47 

47 

TROUBLESHOOTING 

FAULT 

PROBABLE CAUSE 

REMEDY 

Machine does not power 
up 

Wrong or non-existent input 
power source. Blown fuse or 
tripped circuit breaker. 

Check input power and verify 
voltage 
Check and replace fuses. Reset 
circuit breakers 

Oil leaking from breather  Normal expansion of gearbox oil 

Let oil purge from gearbox and 
take no further action. 

Home position is not in 
correct position. 

Loss of power during bending, 
or service work was performed 

Go to homing screen on 
controller and repeat homing 
sequence. If not accessible, 
contact factory. 

Material slips in hook arm 

Too much oil on tubing or oil is 
on the die groove. Clear Radius 
is too tight. Material has too thin 
of wall thickness. 

Clean material and die groove 
with solvent. Increase clear 
radius. Increase wall thickness. 
Material may need to be 
clamped top hook arm to 
prevent slipping. Only the 
counter die should be lubed 

Poor bend results 

Worn counter die. Worn die 
groove. Wrong size material and 
or wall thickness. Too tight of a 
clr. 

Replace counter die. Replace 
die. Verify material size is 
correct. Verify clr 

Twisting material 

Bend die is not bolted down, 
Misaligned counter die, worn 
spindle bearing 

Verify the bend die is bolted 
down to the spindle. Check 
counter die alignment. Replace 
spindle bearing 

Machine overloads and 
wont bend 

Material is too big for machines 
capacity. Tensile strength of 
material is too high. Input power 
is too low. Bending speed is too 
fast. No lube on counter die. 

Verify material wall thickness 
and diameter for capabilities. 
Get material with lower tensile 
strength. Lower bend speed. 
Verify input power. 

Inaccurate bending 

Counter Die leadscrew position 
is changing. Material diameter is 
not consistent 

Verify that the counter die 
leadscrew is holding its position 
via the counter. Check material 
diameter with a caliper to verify 
size. 

Содержание RDB-250
































































Отзывы: