background image

 

 

26 

26 

5.  The stop block (B) can be set at different positions by loosening the lock bolt (B also), sliding 

the guard and shaft assembly upward, and then tightening the lock bolt to hold the guard at 
that position. 

 
 

OPERATING PRECAUTIONS 

 
The following operating and safety precautions must be observed in order to avoid harm to the 
operator or damage to the drill press. 
1.  Safety is the responsibility of the user/purchaser since conditions differ between jobs. Use 

and enforce safety procedures at each operation location and provide for any changes in 
conditions to provide maximum safety. 

2.  The head assembly must be locked to the column, so the thrust produced by drilling will not 

force the head assembly up the column. 

3.  The worktable must be locked to the column so it will not be forced down the column. 

4.  DO NOT start to drill the workpiece until making certain the workpiece is held down 

securely. Secure clamping and vises are preferred. 

5.  Make sure the drill is secured in the spindle or check before attempting to use the drill press. 

6.  Make sure the spindle taper is clean and free of burrs, scoring, and galling to assure 

maximum gripping. 

 
 

OPERATION 

 

 

 
1.  Secure drill bit in the chuck. Insert the drill into the chuck jaws at least 1" (25.4mm) when 

possible but do not insert it so far that the jaws touch the flutes of the drill. Verify that the drill 
is centered in the chuck and tighten securely with the chuck key. 

2.  Set the table to the desired height and verify it is securely locked. Allow for any clamps or 

vises. Adjust the safety guard as necessary. 

3.  Set the depth stop as needed. 

4.  Load and secure the piece part to the table. If not using a clamping devise, position the 

material against the left side of the column to prevent the material from spinning during the 
drilling process. 

CAUTION: 

Always  wear  proper  eye  protection  with  side  shields,  safety 

footwear, and leather gloves to protect from burrs and sharp edges. 
When handling large heavy material make sure they are properly supported. 

Содержание DP-3814B









































Отзывы: