Baier BFS, Инструкция по эксплуатации

Страница: 22 / 64

| 22 |
EN
4 Before Starting Work
To ensure safe working with the walk-behind sys-
tem, the following points must be observed before
each use:
•
Read through all safety instructions and hazard
information in this instruction manual and in
the instruction manual of the diamond channel
cutter used.
•
Wear protective clothing such as hard hat,
hearing protection, safety footwear, face
protection or safety goggles, safety gloves and if
necessary, an apron.
•
Connect a suitable dust extractor (e.g. BAIER
special dust extractor).
5 Adjusting the walk­behind
system to the Baier diamond
channel cutter to be mounted
The following Baier diamond channel cutters can be
mounted on the walk-behind system:
BDN 452, BDN 453, BDN 454, BDN 455,
BDN 463 / 4, BDN 464 / 4, BDN 466 / 6 or BDN 511.
The fixing of the diamond channel cutters onto the
walk-behind system differs as follows:
•
2 In the case of the BDN 452, BDN 453,
BDN 454, BDN 455, BDN 463 / 4, BDN 464 / 4
and BDN 466 / 6, the protective hood of the
diamond channel cutter is fixed onto the
walk-behind system using a hexagon bolt M8 (1),
a flat bracket (6) and an angle bracket, right (8).
•
2 In the case of the BDN 511, the protective
hood of the diamond channel cutter is fixed onto
the walk-behind system by a mushroom head
bolt M8 (4) or a hexagon bolt M8 (1), an angle
bracket, left (5) and an angle bracket, right (8).
It is possible to replace the flat bracket with the an-
gle bracket, left and vice versa (the flat bracket and
angle bracket, left can be ordered from Baier, see
Chapter “Tools and Accessories” on page 25).
5.1 Modifying the walk­behind
system
DANGER
Risk of injury due to electric shock.
Î
Disconnect the mains plug before carrying out
any work on the walk-behind system and the di-
amond channel cutter.
Dismantling:
•
2
Remove the hexagon nut M8 (9) and mush-
room head bolt M8 (4) or hexagon bolt M8 (1)
from the retainer for the protective hood.
•
2 Unscrew star knob (12).
•
2 Remove the angle clamp (11) of the guide
indicator.
•
2
Unscrew both hexagon nuts M8 (10) on the
angle bracket, right (8).
•
2 Remove angle bracket, right (8).
•
2
Remove the two hexagon socket head
screws M8×50 (2) and M8×65 (3) with flat b
bracket (6) or angle bracket, left (5).
Mounting:
•
2 Select the corresponding fixing – flat brack-
et (6) or angle bracket (5), left according to the
Baier diamond channel cutter to be mounted,
see Chapter “Adjusting the walk-behind system
to the Baier diamond channel cutter to be
mounted” on page 22.
•
2 Push the hexagon socket head bolt
M8×50 (2) through the back of the flat brack-
et (6) or angle bracket, left (5) and guide (7).
•
2 Push the hexagon socket head bolt
M8×65 (3) through the front of the flat bracket (6)
or angle bracket, left (5) and guide (7).
•
2 Push the angle bracket, right (8) onto the two
hexagon socket head bolts (2) / (3).
•
2
Screw one hexagon nut M8 (10) each onto
both hexagon socket head bolts (2) / (3) and
tighten (tightening torque: between 20 and 25
Nm).
•
2 Push the angle clamp (11) of the guide
indicator onto the front, longer hexagon socket
head bolt M8×65 (3).
•
2 Screw on the star knob (12) and fix the angle
clamp (11) of the guide indicator.
•
Mount the Baier diamond channel cutter onto
the walk-behind system, see Chapter “Mounting
the walk-behind system on the diamond channel
cutter” on page 23.