background image

Nova-436 Outdoor LTE TDD Base Station Installation Guide 

 

 

About This Document 

This  document  is  a  guidance  of  Nova-436  hardware  installation  for  installation 

personnel,  including  the  preparation  of  installation  tools  and  supporting  materials, 

the demands for installation environment, installation  procedure, cable connection 

and power on. 

Accomplish  the  installation  of  the  device  according  to  this  guide,  the  installation 

personnel  can  avoid  potential  damage  to  the  device  during  the  installation 

procedure, which makes sure the subsequent good running of the device.   

This document is suitable for model mBS2130. 

 

Copyright Notice 

Baicells copyrights this specification. No part of this specification may be reproduced in 

any form or means, without the prior written consent of Baicells. 

 

Disclaimer 

This  specification  is  preliminary  and  is  subject  to  change  at  any  time  without  notice. 

Baicells assumes no responsibility for any errors contained herein. For more information, 

please consult our technical engineers. 

 

Disposal of Electronic and Electrical Waste 

Pursuant to the WEEE EU Directive, electronic and electrical waste must not 

be  disposed  of  with  unsorted  waste.  Please  contact  your  local  recycling 

authority for disposal of this product.

 

 

Revision Record 

Date 

Version 

Description 

30 Oct, 2017 

01 

Initial Released. 

16 Jan, 2018 

02 

Optimize descriptions and fix some bugs. 

 

Contact Us 

Baicells Technologies Co., Ltd.   

Address: 3F, Bldg A, No.1 Kai Tuo Rd., Haidian Dist., Beijing, PR China, 100085 

E-mail: [email protected]/[email protected] 

Tel: 400-612-0167 

Fax: +86-10-62607100 

Содержание Nova-436




























Отзывы: