BAGRAM RGB STX-1796 Скачать руководство пользователя страница 14

Страница: 14 / 18

www.stairslight.com

Changing RGB programs

To change the RGB program briefly press the CON (steady light) button to turn on the lights the

whole staircase. Now, briefly pressing the PRG button, you can sequentially change RGB programs

of the controller. The effect is visible immediately on the stairs. When changing programs will be

displayed colored markers. This allows you to assess where in the list of programs just are. See a

list of RGB programs on page 3.

Most programs have additional options changed by pressing the OPT button. Most often it is the

speed of change of the color or the selection of a particular color. Set program and its options are

stored by the controller.

The controller is factory-enabled range of special programs (FX). This range can be switched on

and off. After turning off the number of programs is restricted to the basic programs and after program

14 (black marker - off), the controller will go directly to the program 1.

To lock and unlock FX mode, hold both (PRG and OPT) buttons in for about 15 seconds until the

LEDs changes from blue to either red (locked out) or green (unlocked). If both program and option

buttons are pressed together briefly the unit will revert to program 1.

After any buttons have been pressed the changes will be stored to non volatile memory and the

unit will power up in that mode until further changes are made.

When you change the program, turn off the lighting of the stairs again briefly pressing the ECON.

After approx. 5 seconds, the controller will return to normal operation.

Rotation programs can be enabled by changing the parameters of the controller - see the next

chapter point: Flicker 4: Automatic switching programs RGB.

Adjusting the controller

Setting the parameters should be performed only when strictly necessary, after reading the

following description carefully. For your greater safety, changing these parameters is blocked by

the factory. They can be unblocked by the user only when he understands the method according to

which they are set.

To start the parameter setting mode, press and hold the

SETUP

button for about 20 seconds (it

stars lighting up the steps) until the green

LED

fades out. Release the button to go on to the controller

parameter setting mode. A few seconds flickering of the

LED

corresponds to each parameter. You

can set or change 12 parameters, and therefore there will be twelve consecutive flickers of the

LED

In order to facilitate counting them, a marker is inserted after every five flickers – a two second

LED

constant light. To select a specific parameter to be changed, you should count each flicker and then,

after a suitable number of flickers, press the

SETUP

button. If you do not want to change a parameter,

skip the flickering without pressing the button. If at the parameter setting mode the

SETUP

button is

not pressed, none of the parameters will change.

The principle of setting the parameters is as follows: setting each parameter is indicated by a

rapid flickering of the green

LED

. If during this flickering the

SETUP

button is pressed and held, then,

depending on the parameter, you will see from one to several dozens of slow

LED

pulsees. Setting

Adjusting controller parameters diagram

Содержание RGB STX-1796



















Результаты поиска

Содержание RGB STX-1796

Отзывы:

Бренды по названию

Популярные бренды

BAGRAM RGB STX-1796, Руководство пользователя

Результаты поиска

Содержание RGB STX-1796

Отзывы:

Бренды по названию

Популярные бренды