manualshive.com logo in svg

Baer UniMod GSM-4, Руководство пользователя

Поделиться
Скачать
Baer UniMod GSM-4 Скачать руководство пользователя страница 6

UniMod GSM-4 

 

6 

 

2 

Safety Precautions for the User 

Aircraft safety 

Cellular  engines  can  interfere  with  an  aircraft’s  navigation  system  and  its 
cellular  network. The  use  of  UniMod  GSM-4  on board  aircraft  is forbidden 
by  law.  Failure  to  comply  with  this  prohibition  may  lead  to  temporary  sus-
pension  or  permanent  cancellation  of  cellular  engine  services  for  the  per-
son who infringes this prohibition and/or to legal action against said person. 

Environments with explosive substances 

a) Users are advised not to use the device in automotive service stations. 

b) Users are reminded of the necessity to comply with restrictions regarding 
the  use  of  radio  devices  in  fuel  depots,  chemicals  plants  and  locations 
where explosives are ignited. 

Non-ionising radiation 

As is the case with other mobile radio transmitters, operating personnel are 
advised to use the device in the normal operating position only in order to 
ensure optimum performance and safety. Avoid touching the antenna. 

Personnel 

Installation and repairing should be done by experienced personnel only. 

Connecting to other devices 

In  order to  connect the UniMod  GSM-4  to  another  device  please  read the 
device’s operation manual to obtain detailed information about safety. Don’t 
connect devices, which are not approved by manufacturer. 

Precautions in the event of loss/theft of the Cellular Engine and 
the SIM card 

If your UniMod  GSM-4, your SIM card or both go missing, notify your net-
work operator immediately in order to avoid misuse. 

 

Содержание UniMod GSM-4



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды