background image

 

UniMod GSM-4 

 

General 

The  world-wide  GSM  radio  networks  (GSM  =  Global  System  for  Mobile 
communication) provide besides digital voice communication the possibility 
to  transmit  data.  In  this  operation  mode  it  is  possible  to  send  fax,  data 
(CSD:  Circuit  Switched  Data  connection),  GPRS:  General  Packet  Radio 
Service)  and  short  messages  (SMS).  The  universal  radio  modem  UniMod 
GSM-4  is  supposed  for  remote  inquiry  of  measurement  data  of  any  kind, 
especially however for telecounting applications. 

The UniMod GSM-4 supports in the operation mode GPRS the meter data 
communication according to DIN 43863-4 (IP-Telemetry). 

 

1.1 

Requirements 

The  UniMod  GSM-4  can  be  used  in  any  EGSM  850/900/1800/1900  MHz 
network  with  an  arbitrary  number  of  providers.  It  requires  however  the  in-
frastructure  for  operating  mobile  stations  with  2  Watt  (Class  4;  850/900 
MHz) or 1 Watt (Class 1; 1800/1900 MHz) transmission power. The modem 
supports an interface for 3V SIM cards. For communication a SIM card with 
call number for 9600 Baud transmission is needed. 

For  the  UniMod  GSM-4  communication  modules  produced  by  internation-
ally  renowned  companies  are  used.  These  companies  update  their  soft-
ware  packages  regularly  and  add  or  change  features.  The  software 
releases are continuously checked by the development department, but no 
responsibility  for  this  software  releases  can  be  taken  over  except  of  war-
ranty granted by the module producer. 

 

Содержание UniMod GSM-4



































Отзывы: