background image

Page 11

For technical questions, please call 1-888-866-5797.

Item 56528 
        

S

AFE

ty

O

PERA

ti

O

n

M

A

int

E

n

A

n

CE

S

E

tu

P

7.  Hook onto the object using a pulling point, 

tow strap, tree strap, or chain.  See Figure H.  
Shackle not shown between tree strap and hook.

Figure H:  using a strap anchor point

Do not wrap the Wire Rope around 
the object and hook onto the 
wire rope itself.

  

This can damage the object being 
pulled, and kink or fray the Wire Rope.

8.  Attachment point must be centered in 

loop of hook and the hook’s safety clasp 
must be fully closed.  See Figure I.

Figure i:  Correct and incorrect hook attachment

9. 

Do not use a Recovery Strap while winching.

   

They are designed to stretch and can 
suddenly whip back towards the operator 
during a winching operation.

10.  Place a heavy blanket or winch damper 

(sold separately) over the Wire Rope span 
6 feet from the hook to help absorb the 
force released if the Wire Rope breaks.

Figure A: Whiplash Dampening 

Blanket or Winch Damper

11.  Move the Clutch Knob to the Engaged position.  

See the instructions for your Winch model 
under 

Clutch Operation

 on page 10.

WARninG!

 Do not allow anyone to stand near the 

Wire Rope, or in line with the Wire Rope behind the 
Winch while it is under power.  If the Wire Rope should 
slip or break, it can suddenly whip back towards the 
Winch, causing a hazard for anyone in the area.  
Stand well to the side while winching.

Double Line Rigging

a.  A double line system should be used whenever 

possible.  It reduces the load on the winch, 
allowing it to work longer with less heat buildup.  
It reduces load on the winch in two ways:
•  It utilizes the lower layers of wire rope 

that have higher capacity, and

•  It halves the load on the winch 

through pulley action.

b.  Connect the wire rope for a double line 

system as shown in Figure J below.  Use a 
snatch block (sold separately) properly rated 
for the load to be pulled and designed to 
be operated with this winch’s wire rope.

Stationary 

Winching Vehicle  

(Chock tires, 

set parking brake, 

and leave in neutral)

Load

Damper

Figure J:  Double Line setup

c.  Loop the wire rope around the snatch block and 

connect to another part of the vehicle’s chassis or 
to a separate anchor point.  

Do not anchor the 

Wire Rope back to the winch or winch mount.

note:

 If anchoring the winching vehicle, 

only attach the anchor line to the front of the 
vehicle.  If the anchor line is attached to the 

rear of the vehicle, the vehicle′s frame may be 

damaged by the forces exerted by winching.

12.  Operate the controls briefly to 

ensure they work properly.
•  The IN position should retract the winch cable.
•  The OUT position should power out the cable.
If operation is reversed, the power cables 
may be connected backwards.  
Correct any such issue before use.

13.  When it is safe to do so, use the power switch on 

the Controller to retract the Wire Rope, and winch 
the item as desired.  

Do not power the hook all 

the way into the fairlead to prevent damage.

Содержание ZXR 3500

















Отзывы: