background image

Page 10

For technical questions, please call 1-888-866-5797.

Item 56258 

        

SAF

ETY

O

PE

RA

TI

O

N

M

A

INT

EN

A

N

CE

SE

TU

P

Basic Operation

Note:

 If a winch is to be used to pull a vehicle, 

it should optimally be rated to a single line 

pull at least twice the vehicle’s weight.

1.  Examine the Wire Rope.  Do not use the Winch 

if the Wire Rope is frayed, kinked or damaged.

2.  Fully charge the vehicle’s battery.

3.  Check the Winch’s electrical connections. 

All connections must be tight and clean.

4.  Put the vehicle’s transmission in Neutral.

5.  If the vehicle where the Winch is mounted 

is not supposed to be moved, engage the 

emergency brake and block the wheels 

using wheel chocks (sold separately).

6.  To pull out the Wire Rope, move the Clutch Handle 

to the Released position

see instructions for your 

Winch model under the 

Clutch Operation

 section.  

Slide the loop of the Hook Strap over the Hook, then 

pull on the Hook Strap to pull out the Wire Rope. 

WARNING!  TO PREVENT SERIOUS 

INJURY:  Leave at least five full turns 

of Wire Rope on the drum.

7.  Hook onto the object using a pulling point, 

tow strap, tree strap, or chain.  See Figure G.  

Shackle not shown between tree strap and hook.

Figure G:  Using a strap anchor point

Do not wrap the Wire Rope around 

the object and hook onto the 

wire rope itself.

  

This can damage the object being 

pulled, and kink or fray the Wire Rope.

8.  Attachment point must be centered in 

loop of hook and the hook’s safety clasp 

must be fully closed.  See Figure H.

Figure H:  Correct and incorrect hook attachment

9. 

Do not use a Recovery Strap while winching.

   

They are designed to stretch and can 

suddenly whip back towards the operator 

during a winching operation.

10. Place a heavy blanket or winch damper 

(sold separately) over the Wire Rope span 

6 feet from the hook to help absorb the 

force released if the Wire Rope breaks.

Figure A: Whiplash Dampening 

Blanket or Winch Damper

11.  Move the Clutch Handle to the Engaged 

position.  See the instructions for your Winch 

model under 

Clutch Operation

 on page 9.

WARNING!  TO PREVENT SERIOUS INJURY:

 Do 

not allow anyone to stand near the Wire Rope, or 

in line with the Wire Rope behind the Winch while 

it is under power.  If the Wire Rope should slip 

or break, it can suddenly whip back towards the 

Winch, causing a hazard for anyone in the area.  

Stand well to the side while winching.

Содержание ZXR 2500

















Отзывы: