background image

1) 

Includes glue, repair material and a valve wrench.

2) 

The valve wrench inserts into the open valve by 

matching the teeth on the wrench to the slots in 

the valve.

3) 

You can tighten your valve by turning the wrench 

to the right.

4) 

You can loosen and remove your valve by 

turning it to the left. 

1) 

Remove the valve cover from the valve.

2) 

Push the inflation pin down, 

clicking it into the 

down position.

 Board will begin to deflate.

3) 

Start rolling the board from the nose of the 

board 

leaving the valve in the open position.

4) 

Continue to roll until you reach the fins.

5) 

Secure the board with the Double D-ring Strap. 

Insert strap end through the d-rings, double back 

through one d-ring,

 then pull tight.

6) 

Open your bag and set the board and paddle 

into the bag.

7) 

Place your pump and hose into the bag.

8) 

Zip it all up and you’re ready to hike to your next 

adventure, or store your board for the winter.

DEFLATING AND PACKING 

UP THE BOARD

REPAIR KIT

FAQS

//

 

HOW SHOULD I STORE MY BOARD?

You can store your board in a variety of ways. It is ok to 

leave your board inflated for long periods of time, just be 

sure to bleed some air out of the board (recommended 

pressure 12psi) if it will be in the sun or heat. Sun will 

eventually damage the paddleboard if it is left out for 

long periods of time. It is also ok to store your board 

deflated, rolled and in the bag. Storing the board in cold 

temperatures, like an unheated garage, will not damage 

the board.

//

  CAN I PUT MY BOARD ON MY  

ROOF RACK?

You can transport your inflatable board on your vehicle’s 

roof rack, just be sure to bleed air out of the board until 

you reach 12 PSI before placing the board on your roof 

rack in full sun or hot temperatures. 

//

  MY PADDLEBOARD HAS A SLOW LEAK, 

WHAT SHOULD I DO?

Check that the inflation valve is tight. The vast majority 

of slow leaks are fixed by using the included valve 

wrench to tighten the inflation valve. Take care to not 

over-tighten the valve.

//

 

MY VALVE IS TIGHT AND MY BOARD 

STILL HAS A SLOW LEAK?

If you tighten your valve and your board still has a slow 

leak you need to identify where the leak is so you can 

repair it with the included repair kit. Fill a bucket with 

water and add some dish soap. Use a sponge and 

sponge down the board with soapy water. When you 

find an area where you see evidence of air escaping, 

use a marker to identify the area. Use the included 

repair kit to glue on a patch over the leak. If your board 

has more substantial leaking or damage please contact 

[email protected] for help contacting a 

professional repair shop.

//

 

WILL ROCKS DAMAGE MY BOARD?

Bumping into or scraping rocks will not typically 

damage your inflatable board, however continuous 

rubbing or scraping on rocks or other hard surfaces 

may cause damage over time.

//

 

CAN I TAKE MY BOARD ON THE 

AIRPLANE?

Yes, most airlines will allow you to check your board 

in as luggage. Please check with your airline before 

traveling for specific restrictions.

//

 

ADDITIONAL QUESTIONS OR CONCERNS

Please contact Badfish Customer Service at 

customerservice

@

badfishsup.com

 or 

1-800-519-0805

1

1

4

7

2

5

8a

3

6

8b

4

2

3

Содержание MONARCH










Отзывы: