Bad Boy 7800670 Скачать руководство пользователя страница 14

14

Maintenance

Wheel Drive Control Adjustment

The wheel drive control lever 

(A, Figure 18)

should engage

the transmission when the lever is squeezed back against the
handlebar, and disengage the transmission when the lever is
released.

If the transmission does not fully engage or disengage,
adjustment may be performed as follows:

1. Remove the rear cover from the mower.  Refer to the

section entitled “Rear Cover Removal & Installation”.

2. With the wheel drive control lever in the ‘DISENGAGE’

position, the spring 

(A, Figure 19)

on the end of the

wheel drive control cable should have no tension.
Measure the overall length of the unextended spring 

(B)

.

3. Fully engage the lever, and measure the length of the

extended spring. The overall spring length should
increase by 0.020 – 0.025”.

4. To adjust spring extension:

a.

Disengage the lever.

b.

To increase (+) the extended spring length, loosen 
the jam nut 

(B, Figure 20)

and rotate the ferrule 

(C)

below the adjustment turnbuckle 

(A)

, located on the

lower end of the wheel drive control cable, one-half 
turn out from the turnbuckle.  Tighten the jam nut.

c.

To decrease (-) the extended spring length, loosen
the jam nut, and rotate the ferrule one-half turn in 
toward the turnbuckle. Tighten the jam nut.

5. Engage the lever and recheck the extended spring

length.  Repeat Step 4 as needed.

IMPORTANT: INCORRECT ADJUSTMENT CAN CAUSE
DAMAGE TO THE TRANSMISSION.

www.badboymowers.com

Figure 20: Adjusting the transmission spring tension

WARNING

DO NOT attempt any maintenance, adjustments or service
with engine and blade running. STOP engine and blade.
Disconnect spark plug wire and secure away from spark
plug. Engine and components are HOT. Avoid serious
burns, allow sufficient time for all components to cool.

!

!

Figure 18: Mower drive controls

B

A

B

C

A

+

-

+

-

(Components removed for clarity)

Maintenance (Continued)

Figure 19: Measuring the disengaged transmission
spring length (viewed from below)

A

B

Not 

for  

Reproduction

Содержание 7800670





















Отзывы: