Backyard Play Systems ULTRA PLAYSET 4098 Скачать руководство пользователя

Страница: 6 / 81

SAFETY WARNINGS

This playset has been designed for use by a maximum of ten occupants at one time having a combined

weight of 1,500 pounds. (This weight does not include occupants on the optional monkey bars, glider, or tire swing).

This playset is recommended for children (3) through (11) years of age.

2QVLWHDGXOWVXSHUYLVLRQIRUFKLOGUHQRIDOODJHVLVUHFRPPHQGHG

Instruct children not to walk close to, in front of, behind, or between moving items.

Instruct children not to twist swing chains or ropes or loop them over the top support bar since this may

reduce the strength of the chain or rope.

Instruct children to avoid swinging empty seats.

Teach children to sit in the center of the swings with their full weight on the seats.

Instruct children not to use the equipment in a manner other than intended.

Instruct children not to get off equipment while it is in motion.

3DUHQWVVKRXOGGUHVVFKLOGUHQDSSURSULDWHO\H[DPSOHVZRXOGLQFOXGHWKHXVHRIZHOOÀWWLQJVKRHVDQG

WKHDYRLGDQFHRISRQFKRVVFDUYHVDQGRWKHUORRVHÀWWLQJFORWKLQJWKDWLVSRWHQWLDOO\KD]DUGRXV

while using equipment).

,QVWUXFWFKLOGUHQQRWWRFOLPEZKHQWKHHTXLSPHQWLVZHW6OLSSHU\VXUIDFHVPD\FDXVHDKD]DUG

Verify that suspended climbing ropes, chain, or cable are secured at both ends.

Verify that suspended climbing ropes, chain, or cable cannot be looped back on itself.

,QVWUXFWFKLOGUHQQRWWRDWWDFKLWHPVWRWKHSOD\JURXQGHTXLSPHQWWKDWDUHQRWVSHFLÀFDOO\GHVLJQHGIRU

use with the equipment, such as, but not limited to, jump ropes, clothesline, pet leashes, cables and

FKDLQDVWKH\PD\FDXVHDVWUDQJXODWLRQKD]DUG

Instruct children to remove their bike or other sports helmet before playing on the playground equipment.

Instruct children to not walk or run up slides.

Instruct children to not pick up slides or ramps as this may cause damage or breakage.

3ODFHWKHHTXLSPHQWRQOHYHOJURXQGQRWOHVVWKDQVL[IHHWIURPDQ\REVWUXFWLRQV%HVXUHWRORRN

overhead for any obstructions above the playset.

Do not use the equipment until fully erected per this playset instruction manual, bolts tightened and

the playset is anchored to the ground.

Please read carefully. Observing the following statements and warnings

reduces the likelihood of serious or fatal injury.

NOTICE:

This playset product is not intended for public use. It is intended for residential application

and is not warranted for public or commercial use.

Содержание ULTRA PLAYSET 4098


















































































Результаты поиска

Содержание ULTRA PLAYSET 4098

Отзывы:

Похожие инструкции для ULTRA PLAYSET 4098

Бренды по названию

Популярные бренды

Backyard Play Systems ULTRA PLAYSET 4098, Инструкция по сборке

Результаты поиска

Содержание ULTRA PLAYSET 4098

Отзывы:

Похожие инструкции для ULTRA PLAYSET 4098

Бренды по названию

Популярные бренды