SKU 272-0095/FC-30-MN
05
© 2018 Jack-Post Corporation 09/18
MATERIAL PLAN
4 FOOT LONG TABLE
6 FOOT LONG TABLE
8 FOOT LONG TABLE
LUMBER
CUT SIZES
LUMBER
CUT SIZES
LUMBER
CUT SIZES
Pcs. Length Size
Pcs. Length Size
Pcs. Length
Size
Pcs. Length Size
Pcs. Length Size
9
8 ft.
2 x 4 14
4 ft.
2 x 4
15
8 ft.
2 x 4 14
6 ft.
2 x 4
16
8 ft.
2 x 4
–
–
–
3
28 in.
2 x 4
–
–
–
3
28 in.
2 x 4
–
–
–
–
–
–
6
10 in.
2 x 4
–
–
–
8
10 in.
2 x 4
–
–
–
LUMBER
CUT SIZES
LUMBER
CUT SIZES
LUMBER
CUT SIZES
Pcs. Length Size
Pcs. Length Size
Pcs. Length Size
Pcs. Length
Size
Pcs. Length
Size
5
8 ft.
2 x 6
9
4 ft.
2 x 6
9
6 ft.
2 x 6
9
6 ft.
2 x 6
9
8 ft.
2 x 6
2
8 ft.
2 x 4
3
28 in.
2 x 4
2
8 ft.
2 x 4
3
28 in.
2 x 4
2
8 ft.
2 x 4
–
–
–
6
10 in.
2 x 4
–
–
–
8
10 in.
2 x 4
–
–
–
LUMBER
CUT SIZES
LUMBER
CUT SIZES
LUMBER
CUT SIZES
Pcs.
Length Size
Pcs. Length Size
Pcs. Length
Size
Pcs. Length Size
Pcs. Length Size
1
8 ft.
2 x 10
5
4 ft.
2 x 10
5
6 ft.
2 x 10
5
6 ft.
2 x 10
5
8 ft.
2 x 10
1
12 ft.
2 x 10
–
–
–
1
8 ft.
2 x 4
1
25 in.
2 x 4
1
8 ft.
2 x 4
– – – – – – – – – – – – – – –
Pcs.
Length
Size
14
8 ft.
2 x 4
3
28 in.
2 x 4
8
10 in.
2 x 4
Pcs.
Length
Size
9
8 ft.
2 x 6
3
28 in.
2 x 4
8
10 in.
2 x 4
Pcs.
Length
Size
5
8 ft.
2 x 10
1
25 in.
2 x 4
–
–
–
2x4
’
s
2x6
’
s
2x10
’
s
29-1/2"
28-1/4"
11"
28"
9-1/2"
11-1/4"
TABLE
STEP 2
Measure and draw line across boards 4
"
from one end for 4
'
table,
6
"
from one end for 6
'
table, or 10
"
from one end for 8
'
table.
DRAW ONE LINE
AT BOTH ENDS OF TABLE
MAINTAIN 1/4" SPACE
BETWEEN ALL BOARDS
8
'
TABLE –10" FROM END
6
'
TABLE – 6" FROM END
4
'
TABLE – 4" FROM END
STEP 3
Center and mark 6 holes in angle bracket on line drawn in STEP 1,
as shown. Drill 1/4" diameter holes.
STEP 4
Attach angle bracket to top boards with six 2" carriage bolts and
hex nuts, as shown.
2X10’S
STEP 5
Repeat STEPS 2 - 4 for opposite end.
CENTER 25" CLEAT
2" CARRIAGE BOLT (6) EACH SIDE
ANGLE BRACKET
1/4" HEX NUT (6) EACH SIDE
SEAT
STEP 1
Layout two 2" x 10"
’
s in the length you have chosen.
STEP 2
Measure and draw lin across one board 4" from end for 4
'
table, 6"
from end for 6
'
table, or 10" from end for 8
'
table, as shown.
Locate and drill two 1/4" diameter holes as indicated by drawing below.
DRAW ONE LINE AT BOTH ENDS OF SEAT
4" FOR 4
'
TABLE
6" FOR 6
'
TABLE
10" FOR 8
'
TABLE
6"
3-1/4"
4"
2"
STEP 3
Repeat STEP 2 for opposite end of seat board and for remaining seat board.
FINAL ASSEMBLY
CENTER BRACKET ON LINE AND MARK HOLES
STEP 1
Attach two tubular legs to angle bracket with 2" slotted head screws
and 1/4" hex nuts.
STEP 2
Fasten the two tubular legs together with two 2-5/8" slotted head screws,
fastening brace between legs through hole as shown.
STEP 3
Make sure tubular leg assembly is at a right angle (90
º
) to the table top.
Bend brace so that it lays flat against table top. Locate the point at which hole in
brace contacts the table top and drill 1/4" diameter hole, as shown.
No cleat used on 4
'
table.
STEP 4
Attach brace to table top with 2" carriage bolt and hex nut as shown.
STEP 5
Repeat STEPS 1 - 4 for opposite end of table top.
STEP 6
Mount benches to leg assemblies with 3-1/4" carriage bolts.
STEP 7
Tighten all bolts.
STEP 1
Layout three 2" x 10"
’
s in the length you have chosen, best side
down on a flat surface, maintaining a 1/4" spacing between boards.
Extra 1/4" carriage bolts can be placed between boards to maintain space.
STEP 6
On 6
'
and 8
'
tables, center the 25" x 2" x 4" cleat between the angle
brackets and nail to the table top boards. Before nailing cleat, cover the
mating surface of the cleat with a coat of white glue. See STEP 3A of
2 x 4 instructions.
