manualshive.com logo in svg

Bacharach Fyrite INTECH, Руководство по конфигурации и эксплуатации

Поделиться
Скачать
Bacharach Fyrite INTECH Скачать руководство пользователя страница 21

Fyrite

 InTech

 

 Manual 

Setup 

 

 

0024-9486 Rev 2 

15 

2.3.  Power Options 

You use the PWR button to turn on the Fyrite

  InTech

.  Power options 

include: 

•

 

Disposable AA alkaline batteries (included) 

•

 

Disposable AA lithium (Li) batteries 

•

 

Externally charged rechargeable NiMH batteries. 

 
Check the Fyrite

 InTech

 for sufficient power prior to each use.  Replace the 

batteries  if the low (or replace) battery symbol  appears in the upper right 
corner of the Fyrite

 InTech

 screen. 

 

 

 

Batteries (4 AA, Fresh or Fully Charged) 

Estimated Life Span in Hours 

(Continuous, Pump On) 

Alkaline (disposable) 

15 hours 

Lithium (disposable) 

20 hours 

Rechargeable 

8 hours 

 

Replace batteries as follows. 

1.

 

Remove the battery cover from the back of analyzer. 

2.

 

If old batteries are installed, remove them and properly discard them. 

3.

 

Observing the polarity markings inside the battery compartment, 

install four ‘AA’ disposable (alkaline or lithium) batteries or four fully-

charged (externally charged) AA rechargeable NiMH batteries. 

4.

 

Replace the battery cover. 

 

 

 

NOTE:  

The  Fyrite

  InTech

  does  NOT charge rechargeable 

batteries.

 

 

 

Содержание Fyrite INTECH









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды