BASIC INSTRUCTIONS FOR USE
1. Men whose skin is sensitive or easily
irritated by shaving, or who suffer from
a skin allergy, should test the shaver
on one section of the leg or arm before
using it.
2.
Remove the UV-disinfecting cap and
turn on the unit to start shaving. Hold
the shaver at a right angle to the area
that you want to shave and run the
double shaving foil carefully along your
skin. Tip: In general, we recommend that
you shave against the direction of hair
growth, as this is the best way to trim
the hair. Pull your skin tight with your
fingers in inaccessible areas to achieve
optimum results.
3. Switch the shaver off each time after
shaving and clean it.
4. Do not push the shaver on the skin too
hard, as this could cause irritation, make
the shaver warm and prevent a perfect
shave.
5. Please note that it takes 2 to 4 weeks for
your skin to adapt to a shaver, so do not
change shaving instruments during this
period of time.
6. If hair is longer than 0.8mm (1/32”),
begin by cutting the hair down first with
a trimmer, then use shaver for a smooth,
close shave.
USER MAINTENANCE INSTRUCTIONS
TAKING CARE OF YOUR SHAVER
Do not remove the shaving foil head while
the shaver is switched on. Always switch
the shaver off!
Ensure that no water gets into the inside of
the shaver to avoid the risk of an electric
shock when it is back in operation.
Never press on the cutters or the shaving
foil and do not touch them with hard
objects as this can cause irreparable
damage to the shaver or parts.
Be careful when dealing with the blades, as
they are very sharp. Risk of injury!
When cleaning, do not apply any detergents
or scouring agents and do not use any
abrasive or sharp objects. They can cause
irreparable damage to the shaver.
NOTE:
When cleaning your shaver, make
sure the unit is turned off.
CAUTION:
•
DO NOT
run shaver, cutters or disinfecting
cap under water. Use only the small brush
(included) to clean the cutters.
• To clean the external surfaces of the
shaver, use a damp cloth. DO NOT APPLY
ANY DETERGENTS.
• To dry, wipe the surface of the shaver
with a dry towel. Do not use a hair dryer
or heater to dry the shaver.
• The shaver should not be used until it has
completely dried.
• Be sure voltage is correct before plugging
in. For connection to power supply not
in Australia abroad use an attachment
plug adapter of the proper configuration
for power outlet. The included adapter
automatically adjusts to the input voltage.
DO NOT USE A VOLTAGE CONVERTER
.
NOTE:
Always replace the cutters and foil
head assembly at the same time.
TO REPLACE FOIL HEAD ASSEMBLY
1.
Remove the foil head assembly by
pressing the round release button
located on the side of the shaver. Hold
the foil head assembly on both sides and
lightly pull away from shaver unit.
2. Take the replacement foil head assembly
(FXLRF2) out of package. Align the
replacement foil head assembly over the
cutters. Carefully move the replacement
foil head assembly down toward the
shaver unit until it firmly snaps into
place.
BE CAREFUL NOT TO DAMAGE
THE FOILS OR CUTTERS WHILE
INSTALLING.
TO REPLACE CUTTERS
1. First remove foil head assembly. Then
remove one cutter by placing your
fingers on each side of it and gently
pulling up and away from the drive shaft.
Repeat with second cutter.
2. Remove the new cutters (FXLRF2) from
the packaging. Align one cutter above a
drive shaft and lightly push down until
it snaps into place. Repeat with second
cutter.
3. Replace the foil head assembly, turn
shaver on to ensure it is working
properly.
DAILY MAINTENANCE:
1.
First remove disinfecting cap from
shaver. Then press the release button
on the side of shaver and remove the foil
head assembly (see Figs. 1 & 2).
2. Use cleaning brush to whisk away any
debris on and around cutter (See Fig. 3).
3. Snap the head assembly closed (see
Fig. 4).
WEEKLY MAINTENANCE:
1.
Repeat steps 1 – 3 from the Daily
Maintenance cleaning steps.
4
5
GOOD
BAD
BENT
BENT
Fig. 1
Fig. 2
Fig. 3
Fig. 4
VERY IMPORTANT:
Cutters must be cleaned and oiled on
a regular basis for proper functioning.
Failure to regularly clean and oil the
cutters will void the warranty.
