AUDIO OFF SETTING
you can turn off the automatic beep indicator if it is not required by sliding the timer switch to 0.
NOTE:
When the 0 setting is selected, there will be no beep indicator to advise when to release
the styler. take extra care when using this setting.
CURL DIRECTION SETTING (Right/Left/Alternate)
use the curl direction control to choose either a uniform or natural finish. select the curl
direction by sliding the switch to either left (l) or right (r) or alternate (A).
(l) starts the curl to to the left, counterclockwise.
(r) starts the curl to the right, clockwise.
you can also select the opposite direction on each side to create a symmetrical look.
When styling the left side of the hair, slide the curl direction switch to the left position (l).
When styling the right side of the hair, slide the switch to the right position (r). this ensures
that the curl sits toward the face on both sides of the head and will give a more uniform style.
For a more natural look, select the alternate setting (A). this will alternate the direction after
each curl.
INSTRUCTIONS FOR USE
• Ensure hair is dry and combed through.
• Plug the styler into a 125V outlet.
• Slide the temperature switch to the required heat setting.
• The styler is ready for use when the ON indicator light has stopped flashing.
• Turn the steam function on if desired. Refer to “STEAM
FUNCTION” and “FILLING THE WATER RESERVOIR”
sections.
• There are 3 time settings; choose the optimum setting for
your hair type. Alternatively, switch the time setting to 0.
• Select the curl direction by sliding the control to either
position l, r or A.
• Separate a section of hair that is no wider than 1 inch
(Figure A). ensure that the section is clean, dry and
combed through.
• Please note the styler must be positioned into the hair
with the opening of the curl chamber facing toward the
head (Figure b).
• Position the styler where you want the curl to start. The
hair section must be straight, and placed neatly through
the center of the styler (Figures c and d).
• Once the hair is in place, let go of the hair section and
close the handle to allow the hair to be automatically
taken into the curl chamber (Figure e).
C
E
D
B
A
TEMPERATURE SETTINGS
There are 3 temperature settings to select from 375°F, 410°F and 450°F. We recommend you
always start with the lowest temperature setting and increase the level of heat as required.
• Setting I (375°F) - for delicate, fine or colored hair
• Setting II (410°F) - for normal textured hair
• Setting III (450°F) - for thick or wavy hair
TIME SETTINGS
there are 3 time settings with an automatic beep indicator. these different settings will give
different curl effects. the longer the hair is held inside the curl chamber, the more defined the
curl will be. but results will also vary according to hair type. use the following as a guide:
• Setting 8 (8 seconds = 3 beeps) - for loose waves
• Setting 10 (10 seconds = 4 beeps) - for soft curls
• Setting 12 (12 seconds = 5 beeps) - for more defined curls
• At the end, there will be 4 quick beeps in succession to indicate time is up, and it’s ready
to release hair.
STEAM FUNCTION:
• Fill reservoir as described in “Filling the WAter reservoir”
• Turn the machine on and allow to heat (red light will stop blinking) before turning on the
steam function. steam function is not recommended if the red light is still blinking
• Slide the steam On/Off switch to ON
• If not using steam, make sure switch is set to OFF
FILLING ThE wATER RESERvOIR:
• To remove the water reservoir, lift the edge up slightly then pull it
out of the unit
• Open the black rubber cap in back of reservoir and fill with distilled
water
• Put the rubber cap back on, making sure it’s completely sealed
• Lock reservoir back onto the unit (you should hear a “click”)
• For your safety, turn the machine off when removing, filling or installing the water reservoir
back onto the unit
1
2
removable water
reservoir (Fill with
distilled water only)
BABNTMC2C IB-14_296A.indd 8-9
1/27/15 4:29 PM
