Page 4
Page 5
BBN01-IM-111109
13.
Begin treatment
a. If a mouthpiece is used, place the mouthpiece between your teeth. With your mouth closed, inhale deeply and slowly through your mouth as
the aerosol begins to flow. Hold your breath for several seconds, then exhale slowly through the mouthpiece.
b. If mask is used, wear the mask and position it over the mouth and nose. As aerosol begins to flow, inhale deeply and slowly through your
month. Hold your breath for several seconds then exhale slowly.
14. After the treatment is complete, switch off the nebulizer by pressing the On/Off switch
and then unplug the unit.
15. Clean the nebulizer according to the “CLEANING” section in the manual.
Nasal cleaning is a special added feature/ function for the Babybelle nebulizer and it can be achieved by follows:
1. Remove the cap (turn counter-clockwise) of the Nasal Spray bottle and fill it with the appropriate volume of physiological saline (9% saline).
2. Place the cap back and turn clockwise to close the Nasal Spray Bottle.
3. Connect one end of the Air Tubing to the Air Outlet Connector “A2” (below the mark A on the nebulizer) and the other end to the Nasal Spray Bottle
set “E” (Bottle body marked with A).
4. Move the Spray Nozzle close to the patient’s nasal cavity with his/her head leaned forward around 30 degree.
5. Switch “On” the nebulizer by pressing the switch ”A1”.
6. Block the pressure release hole on the cap with your index finger and saline will start spraying though the Spray Nozzle on the cap (blocking the
pressure release hole controls the suction pressure - If the pressure release hole is completely closed, it attains the maximum spray pressure. If
the hole is open, there is no spray pressure).
7. Now you can clean the patient’s nasal cavity using the saline spraying through the Spray Nozzle.
8. When cleaning is finished, switch off the nebulizer by pressing the switch “A1” and unplug the nebulizer from the wall socket.
9. Clean the Nasal Spray Bottle set and dry for storage.
1. Use the supplied Air Tubing and connect the Bottle Connector to the nebulizer’s Inlet connector “A3” (below the mark B on the nebulizer)
2. There are Suction Nozzles for adult use and infant use. Please select the correct Nozzle and fit it to the Suction Bottle properly. (Bottle body
marked with B ).
3. Grip the Suction Bottle firmly in the hand and block the pressure release hole by index finger to control the suction pressure.
4. If the pressure release hole is completely closed, it attains the maximum suction pressure. If the hole is open, there is no suction. Adjust the
suction pressure according to the situation during use.
5. DO NOT insert the Suction Nozzle too deep into the nasal cavity or it may injure the soft tissue inside the nasal cavity.
6. To achieve a better suction, clean the nasal cavity by warm water prior to the Suction Bottle usage and rest for 3 minutes.
7. After each use, disassemble the Suction Bottle in separate parts, clean thoroughly and dry for storage.
Switch off the nebulizer by pressing the On/Off switch “A1”.
Unplug the nebulizer from the mains.
Disconnect the Air Tubing and set it aside.
Disassemble mouthpiece parts or mask from the nebulizer set.
Open Nebulizer Set by turning the nebulizer cap counter-clockwise.
Discard the remaining medication in the nebulizer cup.
Wash all items, except tubing and nebulizer, in clean water and non lemon type
dishwashing detergent solution. Rinse thoroughly with warm water to remove the detergent residue. Air dry or hand dry in a clean environment.
When dry, reassemble nebulizer and store the unit.
Never use boiling water to clean any parts.
Never use hi-temperature sterilizing for disinfection (e.g. baby bottle sterilizer).
When needed, only clean the outside of the Air Tubing with dry cloth. Never try to clean the inner wall of the Air Tubing.
If the nebulizer is dirty, follow the step below:
Ensure the switch is in the “Off” position and unplug the power cord from the mains.
Wipe outside of the nebulizer with a clean, damp cloth.
Never use detergent or corrosive substances to clean the nebulizer.
It is recommended to clean the nebulizer every few days to keep it clean and dust free.
Store the nebulizer and accessories in a clean location.
Keep the nebulizer out the reach of unsupervised infants and children. The nebulizer contains small pieces that can be swallowed.
Do not store the Air Tube while there is moisture or medication remaining inside it.
Clean and disinfect the nebulizer kit, mouthpiece or masks before using them for the first time after purchase. Also clean and disinfect the
nebulizer kit if the device has not been used for a long period of time.
CLEANING THE NEBULIZER SET
NOTE: Make sure the Suction Bottle and Nasal Spray Bottle cannot be mixed to use.
CAUTION: To prevent electric shock, DO NOT DISASSEMBLE and never immerse
the nebulizer in water or other liquid or place it under running water. Always disconnect
the unit from mains before you start to clean it. It is recommended to clean all parts
(except the air tubing and nebulizer) after every use.
NOTE: The Spray Nozzle on the cap is very small and blockage after a period of use is
expected. If the Spray Nozzle is blocked, order a new Nasal Spray Bottle cap to get the
related function working properly again.
NOTE: To ensure proper operation of this function, DO NOT connect the Nasal Spray
Bottle set to the air inlet connector on the nebulizer while using this function
SUCTION BOTTLE USAGE
NEBULIZER CLEANING
NASAL SPRAY USAGE
STORAGE
NOTE: Make sure that the Air Tubing is connected to Air Inlet Connector marked B
NOTE: Special care is needed to prevent spilling the medication when attaching the Air
Tube (i.e. keep the nebulizer kit upright).
NOTE: Make sure that the Air Tubing is connected to Air Outlet Connector marked A
