3 - 43
Needle-presser module
Modules
Assembly
3
Presser bar attachment
1. Insert the presser bar bushing
1
into the shaft hole on the bottom of the
unit holder.
2. Attach the plate spring
2
to the unit holder with the screw
1
.
*Key point
• Press the presser bar bushing with the plate spring.
3. Dip the tip of the presser bar
3
(opposite end from the retaining ring) in
FBK OIL RO 100.
4. Insert the presser bar
3
into the presser foot rack
4
.
5. Temporarily attach the screw
2
to the presser bar clamp
5
.
6. Adjust the presser bar height and parallel alignment, and then fully tighten
the screw
2
.
*Key point
• Refer to "Presser bar height and parallel adjustment" on page
4 - 13 for the adjustment procedure.
7. Apply a bead of MOLYKOTE EM30L to the groove on the stopper pin of
the unit holder.
8. Insert spring
and the presser bar clamp
5
into the presser bar
3
.
*Key point
• Engage the stopper pin
6
of the presser bar clamp
5
with the
groove on the stopper pin of the unit holder.
9. Pass the presser bar
3
through to the presser bar bushing
1
.
Dip the tip of the presser bar (opposite end from the
retaining ring) in FBK OIL RO 100.
Dipping
XC8388***
Apply MOLYKOTE EM30L to the groove on the
stopper pin of the unit holder.
Bead
XC8385***
1
Torque
0.78 – 1.18 N·m
2
Torque
Hand tighten
S07
3
2
S07
1
1
2
5
4
6
S07
Taptite, Bind B
M
3X8
Set Screw, Socket (CP)
M5X10
55.7
6.5
SPRING
XC4457***
4
T cam attachment
1. Apply a small amount of MOLYKOTE EM30L to the cam groove
1
and
shaft hole
2
of the T cam.
2. Attach the T cam
3
to the upper unit holder.
3. Apply a small amount of MOLYKOTE EM30L to the gear for the T cam
3
.
Apply MOLYKOTE EM30L to the entire cam
groove in the T cam
Small amount
XC8385***
Apply MOLYKOTE EM30L to the shaft hole in
the T cam
Small amount
XC8385***
Apply MOLYKOTE EM30L to the entire surface
of the gear for the T cam
Small amount
XC8385***
1
3
2
Содержание BLMY
