Baby Jogger City Single Скачать руководство пользователя страница 57

Страница: 57 / 60

CARE & MAINTENANCE

CARE AND MAINTENANCE
Cleaning the Seat Pad:

Refer to the care tag on your seat pad for washing instructions

NEVER use carrier without the seat

pad attached

Cleaning the Shell:

Spot clean using warm water and mild soap

Do not use any other cleaning agents or bleach

Cleaning the Harness Straps:

Spot clean with mild soap and damp cloth

DO NOT SOAK straps in water as this may weaken them

Cleaning the Buckle:

Remove Buckle to Clean
Recline the car seat and locate the metal retainer

Rotate the metal retainer up through the shell

and pad

From the front

pull out the buckle

To clean

place in a cup of warm water and gently agitate the buckle

Press the

red button several times while in the water

DO NOT SUBMERGE THE BUCKLE STRAP.

DO NOT USE SOAPS

HOUSEHOLD

DETERGENTS or LUBRICANTS

Shake out excess water and allow to air dry

Repeat steps as needed until it

fastens with a click

Re-insert the buckle into the same slot it was removed

Pull

up on crotch buckle to make sure it is secured

WARNING!

Inspect and clean buckle from time to time to remove any objects or

debris that could prevent latching

CLEANING HARNESS AND UAS STRAPS

Surface wash only with mild soap and damp cloth

DO NOT IMMERSE THE

HARNESS STRAPS or UAS STRAP IN WATER

Doing so may weaken the straps

If harness straps or UAS belt are frayed or heavily soiled

contact Customer Service at

www

babyjogger

ca or 1-866-744-7177

Содержание City Single





























































Результаты поиска

Содержание City Single

Отзывы:

Похожие инструкции для City Single

Бренды по названию

Популярные бренды

Baby Jogger City Single, Руководство пользователя

Результаты поиска

Содержание City Single

Отзывы:

Похожие инструкции для City Single

Бренды по названию

Популярные бренды