Baby Jogger City Single Скачать руководство пользователя страница 52

Страница: 52 / 60

ACCESSORIES

Harness Covers

Make sure that harness covers do not interfere with placement

of the chest clip at armpit level

To remove

undo the fastening strips and remove

Body Support

Body support must be used if shoulders are below the lowest

harness setting

Never allow body support to bunch or fold behind child

For low birth-weight infants, you must always use the body

support

The body support must be used for infants who

weigh less than 2

7 kg (6 lb)

To remove

unbuckle the buckle and pull out the body support

Head Support

To install

thread the head support straps through the headrest

and use the fastening strips to connect the straps together

To remove

undo the fastening strips and pull the straps out of

the headrest

ACCESSORIES

(on select models)

Содержание City Single





























































Результаты поиска

Содержание City Single

Отзывы:

Похожие инструкции для City Single

Бренды по названию

Популярные бренды

Baby Jogger City Single, Руководство пользователя

Результаты поиска

Содержание City Single

Отзывы:

Похожие инструкции для City Single

Бренды по названию

Популярные бренды