background image

    

 

 

8

speaker connection

The Falcon / The Osprey

      

 

 

 

 

CAUTION

 

        

Installation of the amplifier shall be done in the following steps:

1. Connect the +12V wire, keep in mind this wire has to be fused at the battery as well. 2. Ensure the ground is 

appropriate, then connect it to the amplifier. 3. Connect the switched remote. 4. Reattach negative wire (ground) 

to the battery. 5. Operation over 16V  will cause the amplifier to go into protect & can void the warranty! 

We recommend using  minumum10 Ga speaker cables to acquire the intended performance & efficiency.

Run the speaker cables from your speakers to the amplifier’s mounting location. 

Ensure these are ran separately and away from high current cables and if possible the RCA cables as well. 

In all cases where cables are penetrating the vechile’s chassis use grommets to protect the cable. 

Connect the speaker wires according to the terminals on the speaker(s). Strip 3/8’’ / 1 cm of insulation of the end of 

each cable and twist the cable strands together tightly. Make sure there are no stray strands that could touch other 

cables or terminals as it can cause a short circut. 

Crimp spade plugs over the end of the cable or tin the ends with solder to provide a solid terminal.

Connect the cable ends to the amplifier as shown in the diagram. Note, the amplifier’s speaker terminals are 

internally bridged.

Speaker impedance 1 Ohm ~ 8 Ohm

will reach thermal at a faster rate & will eventually go into protect. 

Impedance load under 1 ohm is not warranted!

Содержание Zero Five The Falcon















Отзывы: