background image

 

 

6  

  

IMPORTANT WARNINGS  

 

 

  

ENSURE   ANY   TRANSIT   PROTECTION   IS   REMOVED   BEFORE 

 

INSTALLING THE APPLIANCE. 

 

THIS APPLIANCE IS NOT INTENDED TO BE INSTALLED OR USED IN A MARINE 
ENVIRONMENT. ENSURE APPLIANCE IS INSTALLED IN A STABLE POSITION.

 

INSTALATION AND SERVICING SHALL BE CARRIED OUT ONLY BY 
AUTHORISED PERSONNEL. 

 

 

 

FAILURE TO DO SO WILL VOID B&S WARRANTY AND MAY RESULT IN DAMAGE TO EQUIPMENT OR INJURY 

TO PERSONNEL. 

 

Please  note  that  checking  and  adjusting  of  burner  pressures  on  commercial  catering  appliances  is  an  obligation  of 

gasfitters. 

 
The relevant  legislation  is as follows from the 

Plumbing Regulations  2008

 administered by the 

Victorian Building 

Authority: 

 Gas fitting work defined

 

(1)  Gas  fitting  work  is  the  construction,  installation,  replacement,  repair,  alteration,  maintenance,  testing  or 

commissioning

 of any pipe, 

appliance

, flue, fitting, apparatus, control or other item that is involved with the 

supply or use of gas and that is fitted downstream of the outlet of a customer billing meter or a consumer's gas 
storage container 

  
As per 

AS/NZS5601.1

, clause 6.11.1, this gas appliance must be 

commissioned

 by a suitably authorized person who; 

  

(a)  Installed the appliance when gas is available at the time of installation; or 
(b)  Makes gas available to the appliance if gas was not available at the time of installation 

  
As per 

AS/NZS5601.1

, clause 6.11.3, the commissioning of this appliance shall take 

full account of special design 

features, the manufacturer’s instructions and the appliance safety requirements

  
As per 

AS/NZS5601.1

, clause 6.11.4, the commission of this appliance shall include all of the following; 

  

(a) 

Testing and purging

 of the appliance and installation as appropriate. 

(b)  Checks to ensure the appliance is in 

safe working order

(c)  Ignition  of  each 

burner

  of  the  appliance  and  where  necessary  adjustment,  in  accordance  with  the 

manufacturer’s instructions.

 

(d)  Testing of 

flue

 performance. 

(e)  Testing of all 

safety devices

 for correct operation. 

(f) 

Instruction

  of  the  consumer,  where  available,  on  the  safe  and  correct  operation  of  the  appliance  and  any 

auxiliary equipment. 

(g)  Handing of the appliance 

operating instructions

 to the consumer, or if the consumer is not present, leaving 

the instructions in a suitable location on the premises. 

 

Installation Instructions  

  

Regulations  

This appliance shall be installed only by authorized persons and in accordance with the ma

nufacturer’s installation 

instructions, local gas fitting regulations, municipal building codes, AS 5601 

– Gas Installations and any other statutory 

regulations.  

 

 

Содержание DSK Series














Отзывы: