background image

12

13

Trouble Shooting

Other Information

Problem

Solution

Unit does not operate.

A 'Di·Di·Di·Di' sound is 

heard from the unit and the 

unit is not operational.

No air is being blown out 

of the Air Outlet.

Air quality still has not 

improved despite operating 

for a long time.

Air speed at Air Outlet 

becomes slow. 

Unit produces abnormal 

noise. 

Unit emits unusual smell, 

odour or smoke 

(also flames or burning).

If the unit is used in a seriously polluted area, the treatment process will 

take longer than normal. It is recommended to operate the unit using it 

high airflow mode until the pollution diminishes.

Filters might require cleaning or replaced. Clean or replace filters.

HEPA Filter may be clogged or blocked. Replace HEPA Filter.

(Please refer to  'Filter Maintenance and Replacement' ).

Make  sure  Air  Inlet  and  Air  Outlet  are  not  be  blocked  by  foreign  matter. 

Remove all surrounding matter which may block the airflow. 

Check whether the unit is correctly connected to its power supply.

Turn on unit.

Check whether the filters have been correctly installed. 

Re-install filters.

Check whether the unit is correctly connected to its power supply.

Check whether the power cord interface is in good service condition.

Make sure all packaging materials are removed.

Make sure all packaging materials are removed.

The unit may be malfunctioning.
Seek advice from service centre or an authorised service provider.

Immediately switch off unit and disconnect its power source. Contact local 

service centre or authorised service provider.

110-240V~ 

Lowest

Highest

Turbo

Lowest

Highest

Turbo

Lowest

Highest

Turbo

300 (L) x 210 (W) x 480 (H)

7

Product Specification

Other Information

Power 

Consumption

(W) 

Mode

Mode

Mode

Rated Voltage

Rated Frequency

Power Supply

Airflow

Volume

(m

³

/hr)

Noise Level

(dB) 

Product 

Dimension

(L x W x H) 

(mm)

Treatment 

System 

Net Weight

(kg)

16

35

40

<80

230

280

38

53

57

50-60Hz

Active Oxygen

Generator

Pre-filter

HEPA Filter

NCCO Reactor

Sterilization

Remove dust and hair

Remove dust, hair and airborne particles such as

allergens and pollen, bacteria, viruses and fungus.

Remove odor, decompose and oxidize harmful

pollutants such as formaldehyde and VOCs.

Содержание NCCO1702








Отзывы: