RELEASE DATE
7-11-14
REFERENCE
NUMBER
INS-1324.2
%ULFN\DUG'ULYH0DGHUD&$86$
)$;
ZZZENOLJKWLQJFRPLQIR#ENOLJKWLQJFRP
B-K LIGHTING
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
3/16” Allen Wrench
Phillips Screwdriver
Level
Hammer
Warning
High Voltage
Hot Surface
NEEDED
FOR
INSTALLATION:
By Others
Transformer
Enclosure
Solid Silicone
Faceplate Gasket
OptiLock™
Transformer Input
Transformer Output
Optical Chamber
Patented ICEE™ Lens
Patented Leveling Collar
Concrete Pour Collar
TENAYA2® ICEE™ SERIES
MR16 Halogen
Component Installation
Proper soil preparation is recommended before installation. See the DIG-IT guide at www.bklighting.com/dig-it for more information.
t
1SPEVDU NVTU CF JOTUBMMFE CZ B RVBMJGJFE QFSTPO JO B NBOOFS
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local
and Provincial Codes.
t
'PMMPXQSPEVDUMBCFMJOGPSNBUJPOBOEJOTUSVDUJPOT
t
2VBMJGJFE1FSTPOOFMNVTUQFSGPSNBMMTFSWJDJOHPSSFMBNQJOHPG
this product.
t
#FGPSFXJSJOHUPQPXFSTVQQMZBOEEVSJOHTFSWJDJOHPSSFMBNQJOH
turn off power at fuse or circuit breaker before service.
t
5IF VTF PG BDDFTTPSZ FRVJQNFOU OPU SFDPNNFOEFE CZ UIF
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause
an unsafe condition and void product warranty.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY
AND INSTALLATION INSTRUCTIONS
t
%POPUCMPDLMJHIUFNBOBUJOHGSPNQSPEVDUJOXIPMFPSQBSU
as this may cause an unsafe condition.
t
/FWFS PQFSBUF UIF GJYUVSF XJUI NJTTJOH PS EBNBHFE MFOT
Lens must be cleaned on regular basis.
t
&OUJSF GJYUVSF NBZ CFDPNF FYUSFNFMZ IPU %P OPU UPVDI IPU
MFOTPSGJYUVSFCPEZ%POPUUPVDIUIFMBNQBUBOZUJNF6TF
a clean, dry, soft cloth to handle the lamp. Oil from skin may
damage the lamp and cause it to rupture.
t
3FQMBDF MBNQ POMZ XJUI DPSSFDU XBUUBHF BOE UZQF PG MBNQ
NBSLFEPOGJYUVSFMBCFM
t
"MM HBTLFUT PSJOHT BOE TFBMJOH TVSGBDFT NVTU CF LFQU DMFBO
during installation and service; failure to do this may cause an
unsafe condition and void product warranty.
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY TO
PERSONS IMPORTANT SAFETY
INSTRUCTIONS
Lighted lamp is HOT!
WARNING - To reduce the risk of FIRE OR INJURY TO PERSONS:
Turn off/unplug and allow to cool before replacing lamp.
-BNQHFUT)05RVJDLMZ$POUBDUPOMZTXJUDIQMVHXIFO
turning on.
Do not touch hot lens, guard, or enclosure (see diagram/
picture).
Keep lamp away from materials that may burn.
Do no touch the lamp at any time. Use a soft cloth. Oil
from skin may damage lamp.
Do not operate the luminaire fitting with a missing or
damaged shield.
SAVE THESE INSTRUCTIONS
· Suitable for wet locations · Suitable for recessed in ground locations
IMPORTANT LISTINGS AND CERTIFICATIONS
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS
1A. For soil installation, clear soil around temporary
cover to prevent debris falling into the housing.
Remove temporary cover and foam spacer.
For Soil
1B. For a concrete installation, break through the
disposable Yellow Installation Cover and foam
spacer with a claw-hammer or pry-bar, then
grasp the cover and pull straight up to leave a
smooth, finished edge.
NOTE: Temporary Cover is recyclable.
For Concrete
