background image

  

Protocol - Modular AC-DSP 

V1_version Feb-2011

 

 

1

 

INTRODUCTION. 

This manual describes the operating mode of the AC-DSP range, coin validators that are part 

of the so-called Modular DSP series. The points covered in this document are therefore valid 

for the following models of validators: 

 

AC6-D2S 

 

AC6-D4S 

 

A6-D2S 

**

 

 

A6-D4S 

**

 

 

 

**

 The previous range of validators called 

A-DSP

 is included in the range of 

validators 

AC-DSP

.  For  more  detailed  information  on  this  point,  consult 

paragraph 1.2 of the manual "Technical Information" 

 

  

 

In this manual the general term AC-DSP will refer to any of the above validators. 

For  full  information  on  the  technical  characteristics  and  operation  of  these  validators,  this 

manual  must  be  complemented  with  the  corresponding  product  manual  "Technical 

Information” available on the Azkoyen website “

http://sat.azkoyen.com

”. 

The AC- DSP validator can operate in three different modes: 

 

Parallel 

 

Timer  

 

Credit. 

Each one will be explained in detail in section 3 - Operation. 

The selection of one or another operating mode is done using dip switches. 

 

 

Содержание A6-D2S




















Отзывы: