manualshive.com logo in svg

Azbil AUR890 Series, Руководство пользователя

Поделиться
Скачать
Azbil AUR890 Series Скачать руководство пользователя страница 5

iii

WARNING

Do not use alarm relay output as safety output.

This device has a limited product life. Beyond the product life, the risk of device failure becomes higher. 
Replace this device within its product life.

CAUTION

To ensure proper operation of this device, follow the directions given in this user's manual 

and in the manuals for the combustion equipment and for any other devices that are used. 

When planning a combustion safety control system, please discuss the details with our sales 

representatives.

Mounting, wiring, maintenance, inspection, calibration, etc. should be carried out by a professional 

with technical training in combustion systems and flame safeguard control devices.

Use this device correctly within the range of the rated specifications stated in the user’s manual.

Not doing so may cause device failure or malfunction.

Make sure that the flame detector does not detect the ignition spark. If the flame detector can 

detect the spark, change the detector's line of sight or change the ignition electrode's position.

Do not install where exposed to any of the following:

• Certain chemicals or corrosive gases (ammonia, sulfur, chlorine, ethylene compounds, acids, etc.)

• Dripping water or excessive humidity

• High temperatures

• Sustained long-term vibration

For mounting and wiring, follow the instructions in this user's manual or in the combustion 

equipment manufacturer's manual.

Connections to this device should comply with the standards for wires and wiring methods that 

are specified in the user's manual. Otherwise, the device may fail or malfunction.

For maintenance and inspection methods, replacement cycle, etc., follow the specifications in this 

user's manual.

When discarding this product, dispose of it as industrial waste, following local regulations.

This device's load-control line is equipped with a fuse. Do not short-circuit the load, or the fuse will 

blow. If the fuse blows, replace this device.

Do not design instrumentation that shuts off the power to this device as soon as alarm output is 

generated. Doing so can corrupt this device’s operation history records.

Содержание AUR890 Series































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды