Azbil AUR455 Скачать руководство пользователя страница 25

Страница: 25 / 68

Chapter 2. Installation, Wiring

Connection with model AUD300C/500C

Connect to the AUD300C or AUD500C as shown.

AUR455

14 15

16 17

White

Yellow

(G)

Blue

(F)

AUD300C/500C

Handling Precautions

•

AUD300C and 500C signal wires (blue and yellow) have polarity. Connect the
blue wire to terminal 14 (F), and the yellow wire to terminal 15 (G). A reversed
connection will damage the tube unit and cause a malfunction.

•

To extend the wiring, use 1.25 mm

600 V PVC-insulated cable (IEC 60227-3),

and keep the wiring no longer than 200 m.

Check of wiring between this device and model AUD300C or AUD500C

Necessary tools: tester

Input impedance of 100 kΩ or more

To check that wiring to this device is correct, remove the tube unit from the

AUD300C or AUD500C and measure the DC voltage between terminals F and G

with the tester as shown below.

Connect the + tester probe (red) to terminal G (yellow lead wire) and the − tester

probe (black) to terminal F (blue lead wire).

>> If the reading is between 160 and 220 V DC, the leads are connected correctly. If

a negative voltage is measured, terminals F and G are reversed.

Terminal G

Yellow lead wire

Terminal F

Blue lead wire

− tester probe (black)

+ tester probe (red)

Terminal

Tester probe

Voltage

− (black)

160 to 220 V DC

+ (red)

Содержание AUR455





































































Результаты поиска

Содержание AUR455

Отзывы:

Похожие инструкции для AUR455

Бренды по названию

Популярные бренды

Azbil AUR455, Руководство пользователя

Результаты поиска

Содержание AUR455

Отзывы:

Похожие инструкции для AUR455

Бренды по названию

Популярные бренды