Ayrton magicpanel 602, Руководство пользователя

Страница: 9 / 20

USER MANUAL _
9
in memory. When the installation is powered on, pairing will be done
automatically.
5. REMOVE RECEIVER FROM TRANSMITTER T1 AND PAIR WITH ANOTHER
TRANSMITTER T2.
Case 1: Removing a receiver
• Activate the REST WDMX function in the fixture menu (see OPTION
DETAILS).
• The “wireless” indicator on the fixture screen should be red. The
receiver fixture is then disconnected from transmitter T1.
• Press the configuration button on transmitter T2 for at least 3 seconds,
and the unit will start to pair with the receiver fixture.
Case 2: Removing all receivers from transmitter T1 to pair all to transmitter
T2
• Press the configuration button on transmitter T1 for at least 5 seconds
to reset pairing with receiver fixtures.
• All green indicators on the receiving fixtures will turn red, indicating that
the receiver fixtures are no longer paired with transmitter T1.
• Press the configuration button on transmitter T2 for at least 3 seconds
to pair it with the receiver fixtures.
Note:
• Unpair receiver fixtures from transmitter after use.
• Do not connect the DMX console to the fixture when it is controlled
via wireless. This could cause interference between the two modes of
operation.
controL PAnEL (mEnu oPtIonS)
A large number of settings are accessible from the fixture’s control panel.
A good working knowledge of it will enhance the fixture’s possibilities.
You can access the Main Menu by pressing the key until the display
flashes.
Cycling through the menus is performed by pressing the , ,
or keys, as required:
Press the key to select the desired menu.
Change the selection by pressing the , or , keys.
Confirm your selection by pressing the key.
Exit a menu at any time by pressing the key.
Notes:
You can return to the display by pressing the
or keys from the
basic display.
If the screen fails to respond, hold the “Mode Esc” key down for at least 3
seconds to free up the display.
The fixture’s menu functions are described in the following table:
Address Set Dmx Addr A001~AXXX DMX address setting
users
m
ode
User Mode Stand Mode
Basic Mode
Extend Mode
User Mode A
User Mode B
User Mode C User’s mode to change
channel numbers
Edit User Max channel
PAN : Preset User modes
options
Status Addr via DMX
No DMX Mode
Pan Reverse
Tilt Reverse
Pan Degree
Tilt Degree
Feedback
Pan/Tilt Spd
Mic Sens.
Hibernation ON/OFF
Close/Hold/Auto/Music
ON/OFF
ON/OFF
630/540
270/540
ON/OFF
Speed 1~ 4
0~99%
OFF, 01M~99M,15M Add. via DMX
Auto run if no DMX
Pan Reverse movement
Tilt Reverse movement
Pan Degree Select
Movement Feedback
Reset Pan/Tilt
Sensitivity of Mic.
Stand by Mode
Service PIN Service PIN
RDM PID
Set IP
Set Device ID
Set LED BIN
Change To BIN Password=XXX
xxxxxx
xxx.xxx.xxx.xxx
xx
LED BIN
Change To LED BIN Service Code“=050”
RDM PID Code
Fans Control Head Control Auto
High
Low Head Fans Speed Mode
Select
Disp.Setting Shutoff Time
Flip Display
Key Lock
DispFlash 02~<60m> <05m>
ON/OFF
ON/OFF
ON/OFF Display shutoff time
Reverse 180 degree
Key Lock
No Signal Flash
Signal Select DMX
WDMX
Art--Net
LED Control Kling-Net OFF
Kling-Net RGB
Kling-Net RGBW
Set Universe xx
Temp. C/F Celsius
Fahrenheit Temperature switch
between °C/°F
Initial Pos. PAN =XXX Initial effect position
Wireless DMX Act&Data Out
Rest WDMX
Trigger DMX Value Disp.
Set To Slave
Auto Program
Music Ctrl. PAN……
Slave1,Slave2,Slave3
Master / Alone
Master / Alone DMX value display
Slave setting
Auto program
Music control
Reset Default ON/OFF Restore factory sett.
Info
Time Info. Current Time
Ttl Life Hrs
Last Run Hrs
Timer PIN
Clr Last Run XXXX(Hours)
XXXX(Hours)
XXXX(Hours)
Password=XXX
ON/OFF
Temp. Info Head Temp. XXX °C/°F
Software Ver V1.0…… Software version
Network IP,Mask,Mac
test
Home All
Pan&Tilt Reset all motors
Reset Pan&Tilt
Test Channel PAN …… Test function
Manual Ctrl. PAN =XXX
: Fine adjustment of
parameters
Calibration --Password--
PAN
: Password “050”
Calbrate and adjust the
effects to standard/right
position
Preset
Select Prog. Prog. Part 1 = Program 1 ~ 10 Program 1
Prog. Part 2 = Program 1 ~ 10 Program 2
Prog. Part 3 = Program 1 ~ 10 Program 3 Select programs to be run
Edit Prog. Program 1
:
Program 10 Program Test
Step 01=SCxxx
Step 64=SCxxx Testing program
Program in loop
Save and exit
Edit Scenes Edit Scene 001
~ Edit Scene 250 Pan,Tilt,……
--Fade Time--
--Secne Time--
Input By Outside Save and automatically
return
manual scenes edit
Scenes Input XX~XX Automat. scenes rec