Axminster Trade AT254SB Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 52

background image

Initial Assembly

20

951539 10” and 12” Sliding Table Kits (Box 1 of 2) and (Box 2 of 2)

Locate and identify the mounting brackets (35) and
the height adjustor blocks (45). These are mounted
on the outside faces of the upper chassis legs. They
are anchored against clamping the plates (36) that
are behind the face of the legs.

NOTE: These clamping plates are ‘loose items’, each
is initially held in place by three M10 x 19mm hex

Line up the holes in the clamping plate in
ready ness for fitting mounting bracket

Mounting plate in position

Fig 62

Fig 63

Unscrew the caphead bolt until the
recessed hole is clear

Attaching the mounting bracket (35) to

the side of the saw bench (1)

Fig 64

Fig 65

36

45

35

Caphead bolt

Fit a bolt (39) through the bottom hole of the
bracket, screw it back into its position. Align the
adjustor block (45) as near vertical as you can
judge and fasten the caphead bolt.

Screw the adjusting caphead bolt back through the
block until it touches the lower face of the mounting
bracket (35). (See fig 66) Nip the securing bolts for

Mounting Bracket/Adjuster Block Assembly

bolts (39). Unscrew the caphead bolt in the height
adjustor block (45), see fig 64, until the recessed
hole for the caphead bolt (39) is clear, fit it through
the height adjustor block and screw it back into its
position. Screw it almost home. Next fit a caphead
bolt through the top hole of the bracket (35), and
with the bracket tilted to one side, screw it back into
its position. (See figs 62-63 and 65)

the mounting bracket. Fit the other bracket in the
same way. NOTE: When screwing the adjusting bolt
back through the block, set it to leave the brackets
at approximately the same height. (See fig 67)

Unscrew the slide rail assembly lift and shift handles
(A) so that the square clamps have plenty of
movement.

«
...
18
19
20
21
22
...
»

Содержание AT254SB





















































Отзывы:

Нет отзывов

Похожие инструкции для AT254SB

Fletcher Saber 250-A

Бренд: Fletcher-Terry Страницы: 17

Бренд: Ferm Страницы: 84

Бренд: Clarke Страницы: 24

Бренд: Vulcan Concept Страницы: 56

Бренд: Draper Страницы: 12

Бренд: Draper Страницы: 20

Бренд: Draper Страницы: 12

Бренд: Shop fox Страницы: 50

Бренд: Panasonic Страницы: 11

Бренд: Panasonic Страницы: 15

EY4542 - CIRCULAR SAW 14.4V

Бренд: Panasonic Страницы: 15

Бренд: Panasonic Страницы: 116

Бренд: Panasonic Страницы: 220

Бренд: Mafell Страницы: 126

Бренд: Silverline Страницы: 40

Бренд: Brobo Страницы: 24

Бренд: EIBENSTOCK Страницы: 36

Бренд: Holzstar Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды