Axminster Trade AT254SB Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 52

background image

Initial Assembly

15

Locate the capping plates for the front rail (24B) and using the self tapping screws (24C), secure
in place. (See fig 35) Set the front rail in position, remembering that it must be slightly inside
the front left hand edge of the main saw table, so that the sliding table does not collide with it.
Tighten ONLY the 3 bolts in the main saw table. Repeat the process for the back rail.

Fig 35

Fig 36

Locate the Rip Fence assembly (20), fit the rip fence assembly to the saw by ensuring the
clamping lug at the rear of the fence is hooked over the back rail (23), lower the fence and
manoeuvre the bracket over the front guide rail (22). (See fig 36)

Micro-Adjuster Assembly

Tighten the Phillips screws securely

Fig 37

Fig 38

Locate the Micro-Adjustor (25) there are two Phillips screws through the adjustor
mounting bracket with square nuts on them. Ensure the nuts are undone sufficiently to allow
them to slide into the channel in the Rip Fence mounting bracket, position as required, normally
slightly to the right of the rip fence, (See figs 37-38) and tighten the screws securely.

25

20

22

Capping plate

Fig 39

Fig 40

Locate the capping plates for the Rip Fence Mounting Bracket (24A) and fit carefully using the self
tapping screws. (See figs 39-40)

24A

24B

24C

«
...
13
14
15
16
17
...
»

Содержание AT254SB





















































Отзывы:

Нет отзывов

Похожие инструкции для AT254SB

Бренд: Wadkin Страницы: 32

Бренд: Powerplus Страницы: 14

Бренд: Inmes Страницы: 28

Бренд: Partner Страницы: 57

Бренд: EINHELL Страницы: 96

Бренд: Oliver Страницы: 22

Бренд: Hafco Metalmaster Страницы: 48

Бренд: TYROLIT Hydrostress Страницы: 33

Бренд: McCulloch Страницы: 44

Бренд: Ryobi Страницы: 38

Бренд: Hitachi Страницы: 19

Бренд: Hitachi Страницы: 42

Бренд: Hitachi Страницы: 72

Бренд: Hitachi Страницы: 87

Бренд: Hitachi Страницы: 68

Бренд: Hitachi Страницы: 72

Бренд: Hitachi Страницы: 100

Бренд: Hitachi Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды