Axminster Craft AC405SS Скачать руководство пользователя страница 2

Страница: 2 / 24

Index of Contents

The symbols below advise the correct safety procedures when using this machine.

Fully read manual

and safety instructions

before use

Eye protection

should be worn

Ear protection

should be worn

HAZARD

Dust mask

should be worn

Cert No: SSA16VHR, SSA16VLR, SSA16HLVHR,
SSA16LVHR, SSA16HLVLR, SC1600LVR,
SSA16LVR F405SC3F SSA16LVLR

Axminster Tools & Machinery Ltd
Axminster Devon
EX13 5PH UK
axminster.co.uk

Type

Scroll Saw

Model

AC405SS

and conforms to the machinery example for which the
EC Type-Examination Certificate No AM 50278793
has been issued by Wendeng Allwin Power Equipment Co., Ltd.
at: No. 18 Sichan Road, Wendeng, Shandong 264400 China

and complies with the relevant essential health and safety requirements.

2006/42/EC
06/42/EC - Annex I/05.2006
EN 61029-1:2009+A11

declares that the machinery described:-

This machine complies with the following directives:

EU Declaration of Conformity

Signed

Andrew Parkhouse
Operations Director

Date: 11/07/2014

EU Declaration of Conformity

What’s Included

General Note

Introduction 04
General Safety Instructions for 230V Machines

Specific Safety Precautions for Scroll Saws

Specification 05
Assembly 06
Mounting the Scroll Saw

Illustration and Parts Description

08-09

Setup and Adjustment

10-11

Operating Instructions

12-13

Changing the Blade

14-15-16

Maintenance 17-18
Troubleshooting 19
Exploded Diagrams/Lists

20-21

Wiring Diagram

Notes 23

EU Declaration of Conformity

Содержание AC405SS

























Результаты поиска

Содержание AC405SS

Отзывы:

Похожие инструкции для AC405SS

Бренды по названию

Популярные бренды

Axminster Craft AC405SS, Руководство пользователя

Результаты поиска

Содержание AC405SS

Отзывы:

Похожие инструкции для AC405SS

Бренды по названию

Популярные бренды