Axminster Craft AC405SS Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 24

background image

Troubleshooting

19

PROBLEM

PROBABLE CAUSES

SUGGESTED REMEDY

Breaking Blades

1. Incorrect tension.
2. Overworked (worn out) blade.
3. Wrong blade being used.
4. Twisting blade in wood.

1 Adjust blade tension.
2. Reduce feed rate or replace blade.
3. Use narrow blades for thin wood,

wider blades for thicker wood.

4. Avoid side pressure on blade.

Motor will Not Run

1. Defective cord,plug or outlet
2. Defective motor.

1. Unplug saw, replace defective parts.
2. Repairs MUST be made by a qualified

technician. Call Axminster Tool Centre.

(Technical Sales Phone: 0800 371822).

Excessive Vibration

(Some vibration is inevitable when

the saw and motor are running)

1. Improper mounting of saw.
2. Unsuitable mounting surface.
3. Loose table.
4. Motor mount is loose

1. See proper mounting instructions.
2. Replace plywood workbench

surface with solid lumber surface.

3.Tighten table clamping knob.
4. Tighten motor mount screws.

«
...
17
18
19
20
21
...
»

Содержание AC405SS

























Отзывы:

Нет отзывов

Похожие инструкции для AC405SS

Бренд: Pattfield Страницы: 68

Бренд: Tanaka Страницы: 16

Бренд: Chicago Pneumatic Страницы: 108

Бренд: Gröne Страницы: 160

Бренд: Grizzly Страницы: 118

Бренд: Virutex Страницы: 24

Бренд: Makita Страницы: 68

Бренд: Dynamics Страницы: 10

POWER PRUNER 99944200530

Бренд: Echo Страницы: 20

Бренд: Scheppach Страницы: 276

Бренд: EINHELL Expert Страницы: 184

Бренд: Goldblatt Страницы: 20

Бренд: Hyd-Mech Страницы: 42

Бренд: Hyd-Mech Страницы: 71

Бренд: AGP Страницы: 16

Бренд: AGP Страницы: 16

Бренд: Xtreme Power Страницы: 12

Бренд: Stomer Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды