manualshive.com logo in svg

Axminster Craft AC216TS, Оригинальное руководство пользователя

Поделиться
Скачать
Axminster Craft AC216TS Скачать руководство пользователя страница 25

Changing the Saw Blade

25

DISCONNECT THE MACHINE
FROM THE MAINS SUPPLY!

1. Raise the saw blade to its highest point, remove the saw 
blade crown guard, remove the five cross head screws that
secure the table insert, place carefully aside and remove the 
table insert, see fig 91-92.

Fig 91-92

2. Turn the saw until the locking bar hole (a) is visible and insert 
the blade locking bar (O) into the hole, see fig 93-94.

Fig 93-94

a

O

3. Hold the locking bar (O) undo and remove the nut using the 
24mm spanner (P), see fig 95-96.  Remove the saw plate washer 
(b) and the saw blade and place to one side, see fig 97-98.

4. Give the interior of the machine, the dust extraction
channels, etc. a thorough clean. Check the new blade for
damage, missing teeth, sharpness etc. Fit the new blade, ensure 
that the teeth are pointing towards the front of the machine. 
Put the saw plate washer onto the shaft and replace the ‘Nut’ 
until finger tight and check the saw is correctly seated.

Fig 95-96-97-98

O

P

5. Tighten up the ‘Nut’, using the blade locking bar (O) to hold 
the shaft steady. Check the riving knife is aligned with the saw 
blade, and correctly positioned. Replace the table insert and 
secure with the cross head screws. Replace the crown guard.
When everything is satisfactory, turn the saw blade once by 
hand to check it doesn’t foul anywhere.

6. Reconnect the machine to the mains supply. Give the
machine a ‘quick’ burst (i.e. quick ON-OFF) check to ensure 
everything is O.K. If everything is satisfactory, continue to use 
the machine.

b

Teeth forward

Содержание AC216TS









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды