Axis B/E Series Скачать руководство пользователя страница 51

Страница: 51 / 56

USER MANUAL

_____________________________________________________________________________________________________________________

Maintenance and repairs of small defects

The scale should be kept clean.

Take care that no dirt gets between the platform and the scale base. If found
any, remove the pan (lift it up), remove dirt and then replace the pan.

In case of improper operation caused by short-lasting power supply decay,
unplug the scale from the mains and then plug it again after few seconds.

If the scale is switched on with empty pan and “Err-b” communicate appears,
the load cell has been mechanically damaged.

It is forbidden to make any repairs by unauthorised persons.

To repair the scale, please contact our nearest service.

Error communicates:

Communicate

Possible cause

Remedy

C-1

...

(over 1 min.)

selftests failed

if displayed more than
1 minute, contact an
authorised service

the scale was switched on with loaded pan

remove a load from the pan

mechanical damage of the load cell

contact an authorised service

pan missing

put the pan on

mechanical damage

contact an authorised service

overloading

remove the load from the pan

mechanical damage

contact an authorised service

indicator does

not appear

unstable ground
vibrations

air flows

place the scale on a stable
ground not affected by
mechanical vibrations and
airflows

scale is damaged

contact an authorised service

taring in progress

as above

taring could not be finished (the load is too
small or B\G key was used)

zero the scale or press B\G
key again

the load is too big to be zeroed

tare the scale (

→

←

)

Содержание B/E Series

























































Результаты поиска

Содержание B/E Series

Отзывы:

Похожие инструкции для B/E Series

Бренды по названию

Популярные бренды

Axis B/E Series, Руководство пользователя

Результаты поиска

Содержание B/E Series

Отзывы:

Похожие инструкции для B/E Series

Бренды по названию

Популярные бренды