Axis 02054-001 Скачать руководство пользователя страница 9

Страница: 9 / 59

AXIS Q35 Series Dome Camera

Configure your device

5. Go to

Video > Stream > H.264 and H.265 encoding

and do one or more of the following:

Select the

Zipstream

level that you want to use.

Note

The

Zipstream

settings are used for both H.264 and H.265.

Turn on

Dynamic FPS

Turn on

Dynamic GOP

and set a high

Upper limit

GOP length value.

Note

Most web browsers don’t support H.265 decoding and because of this the camera doesn’t support it in its web interface.
Instead you can use a video management system or application that supports H.265 decoding.

Set up network storage

To store recordings on the network, you need to set up your network storage.

1. Go to

System > Storage

2. Click

Add network storage

under

Network storage

3. Type the IP address of the host server.

4. Type the name of the shared location on the host server under

Network share

5. Type the username and password.

6. Select the SMB version or leave it on

Auto

7. Select

Add share even if connection fails

if you experience temporary connection issues, or if the share is not yet

configured.

8. Click

Add

Record and watch video

Record video directly from the camera

1. Go to

Video > Image

2. To start a recording, click

If you haven’t set up any storage, click

and

. For instructions on how to set up network storage, see

Set up

network storage on page 9

3. To stop recording, click

again.

Watch video

1. Go to

Recordings

2. Click

for your recording in the list.

Содержание 02054-001




























































Результаты поиска

Содержание 02054-001

Отзывы:

Похожие инструкции для 02054-001

Бренды по названию

Популярные бренды

Axis 02054-001, Руководство пользователя

Результаты поиска

Содержание 02054-001

Отзывы:

Похожие инструкции для 02054-001

Бренды по названию

Популярные бренды