AXIOMTEK ETM830 Series Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 64

background image

ETM830 All-In-One ETX v3.01 SoM User’s Manual

Award BIOS Utility

30

z

Halt On

This item determines whether the system will halt or not, if an error
is detected while powering up.

No errors

The system booting will halt on any errors detected.
(default)

All errors

Whenever BIOS detects a non-fatal error, the
system will stop and you will be prompted.

All, But
Keyboard

The system booting will not stop for a keyboard
error; it will stop for other errors.

All, But
Diskette

The system booting will not stop for a disk error; it
will stop for other errors.

All, But
Disk/Key

The system booting will not stop for a keyboard or
disk error; it will stop for other errors.

Press <Esc> to return to the Main Menu page.

«
...
32
33
34
35
36
...
»

Содержание ETM830 Series

































































Отзывы:

Нет отзывов

Похожие инструкции для ETM830 Series

Бренд: Ubiquiti Страницы: 24

C50FSi - VB Network Camera

Бренд: Canon Страницы: 32

Бренд: Rabbit Страницы: 120

Бренд: dbx Страницы: 2

Бренд: dbx Страницы: 17

Бренд: Black Box Страницы: 9

Бренд: Neo Instruments Страницы: 2

Бренд: VCS Страницы: 118

Бренд: Juniper Страницы: 7

Бренд: Aaeon Страницы: 72

Бренд: Logicube Страницы: 56

Бренд: Radica Games Страницы: 40

Бренд: Airvana Страницы: 90

Бренд: Renesas Страницы: 8

Бренд: Abus Страницы: 98

Бренд: Transition Networks Страницы: 1

Бренд: Abov Страницы: 8

Бренд: Renesas Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды