AXIOMATIC AX180800 Скачать руководство пользователя страница 9

Страница: 9 / 72

UMAX180800, 20 Thermocouple, 2 RTD, 4 Inputs, 6 Relays Dual CAN Controller

Version 1

Page: 9-71

2.3.3 Slew Rate Control

2.4 The controller has an ability to adjust the CAN transceiver slew rate for better

performance on the CAN physical network, see Miscellaneous

The Miscellaneous function block contains various parameters that affect the general
diagnostic performance of the ECU.

The

Undervoltage Threshold

Overvoltage Threshold

, and

Shutdown Temperature

setpoints are used to set the limits for when their respective diagnostic messages are
triggered.

Lastly, the

CAN Diagnostic Setting1

and

CAN Diagnostic Setting2

parameters are used to

control all diagnostics with one general setting for CAN Interface 1 and CAN Interface 2
respectively. This can be used to disable diagnostics entirely, only transmit messages without
a blank SPN, or transmit diagnostic messages normally.

2.5 Diagnostics

The Diagnostic function block includes 120 faults, each representing a diagnostic message
that the ECU is able to produce. Each Universal Input has a Voltage Out of Range Low and
Voltage Out of Range High Faut. Each RTD has Temperature Out of Range Low and
Temperature Out of Range High, High and Low Shutdown Faults. Each Thermocouple Input
has Temperature Out of Range Low and Temperature Out of Range High, High and Low
Shutdown, and Open Circuit Faults. The remaining faults cover VPS Overvoltage and
Undervoltage, Overtemperature, and other faults.

If and only if the

Event Generates a DTC in DM1

parameter is set to true will the other

setpoints in the function block be enabled. They are all related to the data that is sent to the
J1939 network as part of the DM1 message, Active Diagnostic Trouble Codes.

A Diagnostic Trouble Code (DTC) is defined by the J1939 standard as a 4-byte value which is a
combination of:

SPN

Suspect Parameter Number

(first 19 bits of the DTC, LSB first)

FMI

Failure Mode Identifier

(next 5 bits of the DTC)

Conversion Method

(1 bit, always set to 0)

Occurrence Count

(7 bits, number of times the fault has

happened)

In addition to supporting the DM1 message, the Controller also supports
DM2 Previously Active Diagnostic Trouble Codes

Sent only on request

DM3 Diagnostic Data Clear/Reset of Previously Active DTCs

Done only on request

DM11 Diagnostic Data Clear/Reset for Active DTCs

Done only on request

So long as even one Diagnostic function block has

Event Generates a DTC in DM1

set to

true, the Controller will send the DM1 message every one second, regardless of whether there
are any active faults, as recommended by the standard. While there are no active DTCs, the
Controller

will send the “No Active Faults” message. If a previously active DTC becomes

Содержание AX180800









































































Результаты поиска

Содержание AX180800

Отзывы:

Похожие инструкции для AX180800

Бренды по названию

Популярные бренды

AXIOMATIC AX180800, Руководство пользователя

Результаты поиска

Содержание AX180800

Отзывы:

Похожие инструкции для AX180800

Бренды по названию

Популярные бренды