AXIOMATIC AX180800 Скачать руководство пользователя страница 25

Страница: 25 / 72

UMAX180800, 20 Thermocouple, 2 RTD, 4 Inputs, 6 Relays Dual CAN Controller

Version 1

Page: 25-71

When the

“Relay Enable Response”

is set to

‘Enable When ON’

‘Disable When OFF’,

the

relay output will be commanded according to the combined signal of the

“Relay Control

Source”

and

“Relay Control Number”

only when the signal of the

“Relay Enable Source”

and

“Relay Enable Number”

is ON. Otherwise, the relay output is commanded to the OFF

state.

Similarly, when the

“Relay Enable Response”

is set to

‘Enable When OFF’

‘Disable When

ON’

, the relay output will be commanded according to the

“Relay Control Source”

and

“Relay Control Number”

only when the signal of the

“Relay Enable Source”

and

“Relay

Enable Number”

is OFF. Otherwise, the relay output is commanded to the OFF state.

In case the

“Relay Enable Response”

‘Enable When ON Else Keep State’

, the relay output

will be commanded according to the signal of the

“Relay Control Source”

and

“Relay

Control Number”

only when the signal of the

“Relay Enable Source”

and

“Relay Enable

Number”

is ON. If the Enable Signal is OFF, the relay output will keep the previous state.

Likewise, when the

“Relay Enable Response”

is configured to

‘Enable When OFF Else Keep

State’

, the relay output will be commanded according to the

“Relay Control Source”

and

“Relay Control Number”

only when the combined signal of

“Relay Enable Source”

and

“Relay Enable Number”

is OFF. Otherwise, the relay output holds the previous state.

3.6.4 Relay Output Override

The

“Relay Override Source”

will determine whether or not the relay output will be

commanded by the

“Relay Control Source”

. This Source has a higher priority than the

Enable Source.

There are two different

“Relay Override Response”

in which the Override signal can be

used. These responses are listed in

Table 19

Table 19: Relay Override Response Options

Value

Meaning

Override When OFF

Override When ON

When the “Relay Override Response” is configured to ‘Override When ON’, the relay output

will be commanded according to the signal of the “Relay Control Source” and “Relay Control

Number” by the “Relay Override State” only when the override signal is ON. If the “Relay

Override Response” is set to ‘Override When OFF’, the relay output will be commanded only

according to the signal of the Control Source/Number by the “Relay Override State” only when

the override signal is OFF.

Table

shows the two possible states for the “

Relay Override State

”.

In case of

‘Override State OFF’

, the relay output switches to Normally Open. If

‘Override State

’

is configured, the relay output changes to Normally closed.

Содержание AX180800









































































Результаты поиска

Содержание AX180800

Отзывы:

Похожие инструкции для AX180800

Бренды по названию

Популярные бренды

AXIOMATIC AX180800, Руководство пользователя

Результаты поиска

Содержание AX180800

Отзывы:

Похожие инструкции для AX180800

Бренды по названию

Популярные бренды