Axiom CNC Series Скачать руководство пользователя

Страница: 3 / 29

1 I

NTRODUCTION

Thank you for purchasing your AXIOM CNC Safety Enclosure system. Firstly, please inspect

the machine and all components after deliver has been received. Please check and ensure all

aspects of the machine and associated extra items are in good condition and there is no

evidence of damage or wear to any components due to the shipping process.

Please ensure you read the operational manuals for this AXIOM CNC router machine prior to

attempting to use the system.

Responsibility of use or misuse belongs to the end user. BG Precision PTY LTD and its

affiliates accept no responsibility for use or misuse by the user. If you may not be able to use

this product properly, we recommend that you do not begin use or cease use immediately.

If there are any further questions or if anything is not clear, please contact us at

[email protected]

NCLOSURE DESCRIPTION

The enclosure has been constructed to ensure the safe operation of your CNC System. The

machine placed in the interior is accessible from two sides via the dual interlocked doors on

the front and left-hand side of the enclosure. This allows access to all areas of your machine

bed for maintenance, material clamping, tool changing and/or material loading. The

interlocking doors ensure while the machine is active you cannot access the interior of the

enclosure as the doors have a mechanical locking feature. To do so you must engage the reset

condition for your CNC to allow the doors to open.

Placed on the left-hand side of the front and side doors is an E-Stop. Engaging this E-Stop will

activate your reset condition and stop the machine from any operation. The main safety control

panel is located on the front of the enclosure. This help you monitor the current state of the

safety enclosure with a green LED when lit, indicating the machine is active.

The enclosures electronics are all integrated with your CNC Controller to monitor these

conditions. If a door is open or an E-stop is triggered the UCCNC software will not allow you

to activate the machine.

Содержание CNC Series






























Результаты поиска

Содержание CNC Series

Отзывы:

Похожие инструкции для CNC Series

Бренды по названию

Популярные бренды

Axiom CNC Series, Инструкция по сборке

Результаты поиска

Содержание CNC Series

Отзывы:

Похожие инструкции для CNC Series

Бренды по названию

Популярные бренды