SPECIFICATIONS
Model
1
:
AVR-E3A-B
Maximum amplitude
2
:
100V
Rise time (20%-80%):
≤ 1.2 ns
Fall time (80%-20%):
≤ 2.5 ns
Pulse width (FWHM):
10 to 500 ns
Maximum PRF:
200 kHz
Maximum duty cycle:
2%
Required load
5
:
50Ω (±10%)
Polarity:
Positive or negative or both (specify
3
).
DC offset or bias insertion:
Option available
4
. Apply required DC offset or bias in the range of ± 25 Volts,
(250 mA max) to back panel solder terminals.
Trigger modes:
Internal trigger, external trigger (TTL level pulse, > 10 ns, 1 kΩ input impedance),
front-panel “Single Pulse” pushbutton, or single pulse trigger via computer command.
Variable delay (Sync to main out):
0 to 1.0 seconds, for all trigger modes (including external trigger).
Propagation delay:
≤ 160 ns (Ext trig in to pulse out)
Jitter: (Ext trig in to pulse out)
± 35ps ± 0.015% of sync delay
Sync output:
> +3 Volts, > 50 ns, will drive 50 Ohm loads
Gate input:
Synchronous or asynchronous, active high or low, switchable.
Suppresses triggering when active.
Connectors:
Out: SMA, Other: BNC
Power requirements:
100 - 240 Volts, 50 - 60 Hz
GPIB and RS-232 control
1
:
Standard on -B units.
LabView drivers:
Check
http://www.avtechpulse.com/labview
for availability and downloads
Ethernet port, for remote control
using VXI-11.3, ssh, telnet, &
web:
Included. Recommended as a modern alternative to GPIB / RS-232.
http://www.avtechpulse.com/options/vxi
for details.
Settings resolution:
The resolution of the timing parameters (pulse width, delay, period) varies,
but is always better than 0.15% of (|set value| + 20 ns).
The amplitude resolution is < 0.1% of the maximum amplitude.
Settings accuracy, after 10 minute
warm-up:
Amplitude: Typically ± (3% of setting) ± (2% of maximum).
Delay, Period: Typically ± (3% of setting ) ± (5 ns)
Pulse width: Typically ± (3% of setting ) ± (2 ns), at maximum amplitude. As the
amplitude is reduced, the pulse width may shift ± 5 ns. For high-accuracy applications
requiring traceable calibration, verify the output with a calibrated oscilloscope
6
.
Dimensions (H x W x D):
100 mm x 430 mm x 375 mm (3.9” x 17” x 14.8”)
Chassis material:
cast aluminum frame and handles, blue vinyl on aluminum cover plates
Temperature range:
+5°C to +40°C
1)
-B suffix indicates IEEE-488.2 GPIB and RS-232 control of amplitude, pulse width, PRF and delay (see
http://www.avtechpulse.com/gpib
).
2) For operation at amplitudes of less than 10% of full-scale, best results will
be obtained by setting the amplitude near full-scale and using external attenuators on the output.
3) Indicate desired polarity by suffixing model number with -P or -N (i.e. positive or negative) or -PN for dual polarity option.
4) The -OS option adds an internal bias tee circuit to the output, allowing an externally-generated DC offset (±25V/250mA max) to be added the output
signal. The -OT option includes the -OS function, and adds the ability to generate a ±5V/100mA offset internally (controlled from the front panel, or by
computer command).
5) A 50Ω load is required. Other loads may damage the instrument. Consult Avtech (
) if you need to drive other load
impedances.
6) These instruments are provided with a basic calibration checksheet, showing a selection of measured output parameters. These measurements are
performed with equipment that is calibrated on a regular basis by a third-party ISO/IEC 17025:2005 accredited calibration laboratory. However,
Avtech itself does not claim any accreditation. For applications requiring traceable performance, use a calibrated measurement system rather than
relying on the accuracy of the pulse generator settings.
6
Содержание AVR-E3A-B
