background image

651Z 

m542a_m542b_542f_quick_V1.3 

 Package Contents 

 Installation

 

 

 

 

 

 

 

 

QUICK GUIDE 

 

 

For more product details, please visit 

www.surveillance-download.com/user/m521.swf

 

Before starting to set up your camera, please make sure items below are in your box:   

 Standard package: 

 

 

Camera 

Quick Guide 

 Optional accessories: 

 

 

 

Screws, Wall 

Plugs, Rubber 

Rings (

×

3) 

Wrench 

Desiccants 

(

×

2) 

Waterproof accessory kit   

 

Step 1: Uncover the dome camera by loosening the three screws on the housing with the 

supplied wrench. 

Note: The three screws aren’t designed to be removed from the housing. 

Step 2: Attach the supplied installation sticker to your desired installation location.   

Step 3: Locate the three deepest holes on the base. (See Pic 1.) They are where the three 

supplied screws belong.   

On the sticker, make holes where the three screws and the cables are supposed to 
penetrate. However, if the cables won't go through the surface, you don’t need to 
make the hole for them in advance. Next, align the camera with the sticker, putting 
the three screws through the holes, as well as the cables—if necessary. Then, 
tighten the screws. 

 

Pic 1 

 Installation (Continued)

 

Step 4: The lens can be adjusted in three ways: 

 

 

a. Take turn to pan the camera. 

b. Tilt the lens after loosening the two plastic 

screws on either side of the lens. 

c. Remove the protective case by loosening the two 

screws on it before rotating the lens from behind. 

 

 

 

Pan 

Tilt Rotate 

Step 5: Be sure to replace the original desiccant(s) with the new ones. Use 

provided double-sided tape to stick the desiccants in place as 

illustrated below. Keep them inward enough for the housing to close 

nicely. The new desiccants must not be exposed to air for over 30 

seconds. 

Note: Both the two new desiccants are to be put in the camera to remove 

excessive humidity and ensure the camera works well.   

Step 6:

 

Then, clear the lens of fingerprints and replace the housing before 

tightening the screws on it. 

Note: To prevent the fuzzy image due to the IR reflection, please keep the 

transparent cover clear. 

Step 7: Power up the camera. 

 

(TURN BACK TO CONTINUE)

 

Содержание avm420s







Отзывы: