Avtech 14260 Скачать руководство пользователя страница 40

Страница: 40 / 54

PROGRAMMING YOUR PULSE GENERATOR

KEY PROGRAMMING COMMANDS

The “Programming Manual for -B Instruments” describes in detail how to connect the

pulse generator to your computer, and the programming commands themselves. A

large number of commands are available; however, normally you will only need a few of

these. Here is a basic sample sequence of commands that might be sent to the

instrument after power-up:

*rst

(resets the instrument)

trigger:source internal

(selects internal triggering)

frequency 1000 Hz

(sets the frequency to 1000 Hz)

pulse:delay 1 us

(sets the delay to 1 us)

pulse:width 10 us

(sets the positive pulse width to 10 us)

volt:ampl +25.7

(sets the positive pulse amplitude to +25.7 V)

output on

(turns on the output)

For triggering a single event, this sequence would be more appropriate:

*rst

(resets the instrument)

trigger:source hold

(turns off all triggering)

output on

(turns on the output)

pulse:delay 1 us

(sets the delay to 1 us)

pulse:width 10 us

(sets the positive pulse width to 10 us)

volt:ampl +25.7

(sets the positive pulse amplitude to +25.7 V)

trigger:source immediate (generates a single non-repetitive trigger event)

trigger:source hold

(turns off all triggering)

output off

(turns off the output)

To set the instrument to trigger from an external TTL signal applied to the rear-panel

TRIg connector, use:

*rst

(resets the instrument)

trigger:source external

(selects internal triggering)

pulse:delay 1 us

(sets the delay to 1 us)

pulse:width 10 us

(sets the positive pulse width to 10 us)

volt:ampl +25.7

(sets the positive pulse amplitude to +25.7 V)

output on

(turns on the output)

These commands will satisfy 90% of your programming needs.

Содержание 14260






















































Результаты поиска

Содержание 14260

Отзывы:

Бренды по названию

Популярные бренды

Avtech 14260, Инструкция по эксплуатации

Результаты поиска

Содержание 14260

Отзывы:

Бренды по названию

Популярные бренды