Avocent ESP Serial Hub Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 96

Avocent ESP Serial Hub Скачать руководство пользователя страница 59

Chapter 5: Configuration Utility

49

Sending a Break to a Port

The Send Break feature sends a line break to an attached device on one or all ports.

To send a break to a port:

1.

From the Top Menu, enter

4

to select Send Break. The Port Selection Menu will be displayed.

2.

Enter the number corresponding to a port or

0

to select all ports.

3.

A break will be sent to the specified port(s), and a confirmation message will be displayed.
Press any key to continue.

Displaying Hardware Information

The Hardware Information display includes the following items.

•

Model number

•

Hardware revision number

•

Number of serial ports

•

EEPROM revision number

•

Amount of SDRAM in megabytes

•

Amount of Flash memory in megabytes

•

Amount of EEPROM configuration memory in kilobytes (ESP-2 MI and ESP-4 MI hubs only)

•

Hub MAC address

•

Hub serial number

•

Hub part number

This information cannot be modified.

To display hardware information:

1.

From the Top Menu, enter

0

to select Server Configuration. The Server Configuration Menu

will be displayed.

2.

Enter

5

to select Hardware Information.

Displaying or Updating Flash Memory

The Flash Update display includes information about the current images loaded in Flash memory.
You may update the embedded application image or bootstrap image in Flash memory. Before
updating a Flash image, you must configure a TFTP server on the target server system and install
the new Flash image in the appropriate location, which is usually relative to the TFTP
root directory.

To display Flash image information or update an image:

1.

From the Top Menu, enter

0

to select Server Configuration. The Server Configuration Menu

will be displayed.

«
...
57
58
59
60
61
...
»

Содержание ESP Serial Hub

































































































Отзывы:

Нет отзывов