Avocent ESP Serial Hub Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 96

Avocent ESP Serial Hub Скачать руководство пользователя страница 46

36

ESP Serial Hub Installer/User Guide

Sending a Break to a Port

The Send Break feature sends a line break to an attached device on one or all ports.

To send a break to one or all ports:

1.

From the Main Menu, select

Port Break

. The Serial Port Selection window will open.

2.

Select a port number or

all ports

, then click

Apply

.

A break will be sent to the specified port(s).

Displaying Hardware Information

The Hardware Information display includes the following items.

•

Model number

•

Hardware revision number

•

Number of serial ports

•

EEPROM revision number

•

Amount of SDRAM in megabytes

•

Amount of Flash memory in megabytes

•

Amount of EEPROM configuration memory in kilobytes (ESP-2 MI and ESP-4 MI hubs only)

•

Hub MAC address

•

Hub serial number

•

Hub part number

This information cannot be modified.

To display hardware information:

Select

Hardware Information

from the Main Menu.

Displaying or Updating Flash Memory

The Flash Update display includes information about the current images loaded in Flash memory.
You may update the embedded application image or bootstrap image in Flash memory. Before
updating a Flash image, you must configure a TFTP server on the target server system and install
the new Flash image in the appropriate location, which is usually relative to the TFTP
root directory.

To display Flash image information or update an image:

1.

From the Main Menu, select

Flash

.

The Application Image section includes the version number, size and internal slot number for
the Primary embedded application image. The previously installed image is maintained as a
backup; the Backup field contains its values.

«
...
44
45
46
47
48
...
»

Содержание ESP Serial Hub

































































































Отзывы:

Нет отзывов