background image

10 

2

 

Basic operation 

 
 

2.1

 

First operation / self test 

 
In  case  the  CD  6.2  was  not  connected  to  mains  a  self  test  will  be  performed  when  it  is 
switched  on  by  the  mains  switch  (29)  for  the  first  time.  The  unit  will  check  its  configuration 
and that all the installed components work properly. The procedure is shown in the display. 
Afterwards the unit will switch to stand by. 
 
 
 

2.2

 

Switching on / stand by 

 
Using  the  button  power  (1)  you  can  switch  between  on  (operate)  and  stand  by.  When 
switched on, the display (10) lights up and the LED (7) is off. In stand by mode the display is 
off and the LED is on to indicate that the unit is still connected to mains. 
 

CAUTION: 

When switched to stand by the unit is still connected to the mains. In case of a 

thunderstorm or if you leave the house for a longer time we recommend that you switch the 
amplifier off by using the mains switch (29) or pull the mains plug (28).

 

 
 
 

2.3

 

Display 

 
When the unit is on, the display (9) shows information about the current settings and state of 
your CD Player. Apart from informations about the operating status (CD Player, Digital Input 
etc.) the lower line shows you currently active settings of the D/A converter: On the left-hand 
side the sample rate (e.g. "192") and bit depth is displayed. On the right-hand side you will 
find the current filter setting (

SMOOTH

 or 

STEEP). 

 

2.3.1

 

Display in CD player mode 

 

TRACK 

On the left-hand side both the current title is  displayed (big figures) and the total number of 
available tracks of the inserted CD (small figures).  
 

TIME 

At the centre of the display the total duration of an inserted CD is displayed, while stopped 
(

STOP

). As soon as the CD is played (

PLAY

) or paused (

PAUSE

), the time already elapsed of 

the current track is displayed.  
 

STATUS 

On the right-hand side the current operating status is displayed (

STOP

PLAY

PAUSE

). 

 

 

 

Содержание OVATION CD 6.2




















Отзывы: