manualshive.com logo in svg

AVL 415SE, Руководство по обслуживанию

Поделиться
Скачать
AVL 415SE Скачать руководство пользователя страница 13

13

Maintenance 

AVL 415SE Smoke Meter — Maintenance Guide

2.2.2 

Service Engineer - Maintenance Schedule 

For the disposal of environmentally sensitive substances, see the 

AVL 415S 

Smoke Meter Operating Manual

, chapter 

Disposal of Environmentally Sensitive 

Substances

.

Clamping lever

Annually

Visual check. 

If damaged or if any part 
is bent off.

Pump

Annually

Check and replace if necesary.

Every 2 000 - 3 000 oper-
ating hours.

Nipple & hose connec-
tions

Annually

Replace.

Annually

Cleaning of electronical 
boards

Annually

Clean with high purity compressed 
air.

If necessary or defective.

Filters of shop air filter 
unit

Annually

Check and replace if necessary.

once every 1 … 2 years;

much more often for oil 
lubricant compressors:
at least: every 
1 … 2 months

Check valve 

Annually

Check and replace if necesary.

Annually

Pressure reduction 
assembly

Annually

Check.

After assembly.

Pressure switch of shop 
air option

Annually

Check and adjust if necessary.

Annually

Component / Test

Lifetime / 

Service interval

Maintenance 

Replacement 

Tab. 1  

WARNING

Fire hazard

When using the required appliances like sprays, mounting pastes, lubricants, 
always observe the relevant handling instructions and safety measures of the 
various products.

All sprays used are a fire hazard and highly inflammable. Installation work using 
the appliances on and inside measurement devices and on test beds must only 
be carried out on cooled-down parts and in well ventilated areas.

NOTICE

The compressed air used to clean, has to be 

absolutely

 free from oil, water, and 

particles.

Содержание 415SE



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды