Avital 4003 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 48

background image

19

© 2009 Directed Electronics. All rights reserved.

eral Motors product or a Dodge Dakota pickup, please call Directed
Electron ics Technical Support for an alternative shut-down method.
Do not return the vehicle to the customer until this feature is properly
installed!

D2D and programmer interface

The 4-pin red port is for interfacing with an Xpresskit module through
D2D, or you can use it for programming with the Bitwriter®.
If the Xpresskit module is unplugged so the port can be used for Bit-
writer® programming, you must unplug the heavy gauge 6 pin remote
start harness before reconnecting the Xpresskit module back in. Once
the Xpresskit module has been plugged in, reconnect the heavy gauge
6pin remote start harness and proceed to reprogram the Xpresskit mod-
ule.

When the learn routines have previously been programmed using

the Bitwriter®, they may have been locked.
Before proceeding with reprogramming the learn routines, they must
be unlocked with the Bitwriter®, this cannot be done manually with the
Valet switch.

«
...
21
22
23
24
25
...
»

Содержание 4003

















































Отзывы:

Нет отзывов

Похожие инструкции для 4003

UltraGuard PRO 9549UG

Бренд: Audiovox Страницы: 8

Бренд: i-box Страницы: 60

Бренд: Autopage Страницы: 2

Бренд: System Sensor Страницы: 8

Бренд: Omega Research & Development Страницы: 29

Бренд: Excalibur Страницы: 2

Бренд: Trevi Страницы: 6

Бренд: Blaupunkt Страницы: 44

Бренд: By Firstech Страницы: 14

Бренд: TrueGuard Страницы: 5

NIGHT VISION 30330B

Бренд: Equity Страницы: 2

Бренд: Equity Страницы: 2

Бренд: iHome Страницы: 12

Бренд: iHome Страницы: 13

Бренд: iHome Страницы: 20

Бренд: Discovery Kids Страницы: 8

Бренд: Masterbuilt Страницы: 28

Бренд: Fire-Lite Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды