Avital 4003 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 48

background image

26

© 2009 Directed Electronics. All rights reserved.

4.

Activate Input.

Each time the white/blue H1/4 is pulsed, the LED

will turn on or off indicating the feature setting. If the feature has more
than two selections, each time this input is pulsed the next available set-
ting will be picked. For example if 60 minute runtime is chosen, (Menu
2 feature 2) the LED flashes 3 times.

5.

Release.

The Program switch can now be re-

leased.

You can advance from feature to feature by pressing and releasing the
Program switch the number of times necessary to get from the feature
you just programmed to the feature you wish to access. For example,
in Menu One, if you just programmed Feature 1-3 to off, and you want
to program the next feature 1- 4, release the Program switch. Press and
release it once to advance from Feature 1-3 to Feature 4. Then press
the switch once more and

HOLD.

The LED flashes in groups of 4 to

confirm that you have accessed Feature 1- 4.

The learn routine will be exited if any of the following occurs:

The ignition is turned on.

•

The Program switch is pressed too many times.

•

More than 25 seconds elapses between programming steps.

•

«
...
28
29
30
31
32
...
»

Содержание 4003

















































Отзывы:

Нет отзывов

Похожие инструкции для 4003

AVS 24v S Series

Бренд: Manta Страницы: 32

Бренд: Viper Страницы: 37

Бренд: Bellman & Symfon Страницы: 4

Бренд: Cobra Страницы: 28

Бренд: OttLite Страницы: 53

Бренд: Firex Страницы: 7

Бренд: Carpal Страницы: 8

Бренд: Sharper Image Страницы: 5

Бренд: Sharper Image Страницы: 4

Travel Soother SI601

Бренд: Sharper Image Страницы: 7

Бренд: Vision Страницы: 3

Бренд: Code Alarm Страницы: 13

Бренд: Connect2Car Страницы: 24

Бренд: Xtralis Страницы: 2

Бренд: Eurochron Страницы: 8

Smoke Dampers SSSMDR-501

Бренд: Greenheck Страницы: 1

Smoke Dampers SMD-203

Бренд: Greenheck Страницы: 7

Combination Fire Smoke Dampers SSFSDR-511

Бренд: Greenheck Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды